Craftsman 14063 manual Onboard Diagnostics

Page 20

Onboard Diagnostics

OBD2 MONITORS

Fuel System Monitor - This Monitor uses a Fuel System Correction program, called Fuel Trim, inside the on-board computer. Fuel Trim is a set of positive and negative values that represent adding or subtracting fuel from the engine. This program is used to correct for a lean (too much air/not enough fuel) or rich (too much fuel/not enough air) air-fuel mixture. The program is designed to add or subtract fuel, as needed, up to a certain percent. If the correction needed is too large and exceeds the time and percent allowed by the

program, a fault is indicated by the computer.

The Fuel System Monitor is supported by both “spark ignition” vehicles and “compression ignition” vehicles. The Fuel System Monitor may be a “One-Trip” or “Two-Trip” Monitor, depending on the severity of the problem.

Misfire Monitor - This Monitor continuously checks for engine misfires. A misfire occurs when the air-fuel mixture in the cylinder does not ignite.

The misfire Monitor uses changes in crankshaft speed to sense an engine misfire. When a cylinder misfires, it no longer contributes to the speed of the engine, and engine speed decreases each time the affected cylinder(s) misfire. The misfire Monitor is designed to sense engine speed fluctuations and determine from which cylinder(s) the misfire is coming, as well as how bad the misfire is. There are three types of engine misfires, Types 1, 2, and 3.

-Type 1 and Type 3 misfires are two-trip monitor faults. If a fault is sensed on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The MIL is not commanded on at this time. If the fault is found again on the second trip, under similar conditions of engine speed, load and temperature, the computer commands the MIL “On,” and the code is saved in its long term memory.

-Type 2 misfires are the most severe type of misfire. When a Type 2 misfire is sensed on the first trip, the computer commands the MIL to light when the misfire is sensed. If the computer determines that a Type 2 misfire is severe , and may cause catalytic converter damage, it commands the MIL to “flash” once per second as soon as the misfire is sensed. When the misfire is no longer present, the MIL reverts to steady “On” condition.

The Misfire Monitor is supported by both “spark ignition” vehicles and “compression ignition” vehicles.

Catalyst Monitor - The catalytic converter is a device that is installed downstream of the exhaust manifold. It helps to oxidize (burn) the unburned fuel (hydrocarbons) and partially burned fuel (carbon monoxide) left over from the combustion process. To accomplish this, heat and catalyst materials inside the converter react with the exhaust gases to burn the remaining fuel. Some materials inside the catalytic converter also have the ability to store oxygen, and release it as needed to oxidize hydrocarbons and carbon monoxide. In the process, it reduces vehicle emissions by converting the polluting

gases into carbon dioxide and water.

The computer checks the efficiency of the catalytic converter by monitoring the oxygen sensors used by the system. One sensor is located before (upstream of) the converter; the other is located after (downstream

18

Craftsman 14063

Image 20
Contents Page Table of Contents What is OBD? IntroductionYou Can Do It Easy To UseSafety Precautions Safety FirstData Link Connector DLC Location About the Code ReaderVehicles Covered OBD CertifiedControls and Indicators Controls and IndicatorsDisplay Functions Display FunctionsAbout the Code Reader Introduction of Electronic Engine Controls Onboard DiagnosticsComputer Engine Controls Basic Engine Computer Control System Typical Computer Control SystemOn-Board Diagnostics First Generation OBD1 On-Board Diagnostics Second Generation OBD2OBD2 Terminology Not all vehicles support all fifteen Monitors Diagnostic Trouble Codes DTCs 2 0 DTCs and MIL Status OBD2 Monitors OBD2 MonitorsNon-Continuous Monitors Onboard Diagnostics Onboard Diagnostics Onboard Diagnostics Onboard Diagnostics Onboard Diagnostics OBD2 Reference Table DTCName Monitor Preparation for Testing Before YOU BeginUsing the Code Reader Code Retrieval ProcedureLED Erasing Diagnostic Trouble Codes DTCs Using the Code Reader About Repairsolutions Accessing RepairSolutionsHardware Requirements Minimum System Operating RequirementsUsing the Code Reader Vehicle Applications ABS Vehicle Applications Makes CoveredReplacement Parts Warranty and ServicingCraftsman TWO Year Full Warranty