Yamaha RX-V692 RX-V592 owner manual Remote Control IN, OUT terminals, How to Connect

Page 15

English

How to Connect:

Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage this unit and/or speakers.

For connecting to the MAIN SPEAKERS terminals

For connecting to the REAR and CENTER SPEAKERS terminals

Red: positive (+)

Black: negative (–)

2

1

3

➀Unscrew the knob.

➁ Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from

the speaker wires.]

➂ Tighten the knob and secure the wire.

Red: positive (+)

Black: negative (–)

➀

➂

➁

➀Press the tab.

➁Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.]

➂Release the tab and secure the wire.

Banana Plug connections are also possible (except for Singapore model). Simply insert the Banana Plug connector into the corresponding terminal.

For Custom Installer For U.S.A. and Canada models of RX-V692 only

REMOTE CONTROL (IN, OUT) terminals

These terminals are used for custom installation system. When this unit is connected to the components for custom installation system, you can operate this unit with the system remote control.

Connect the REMOTE CONTROL IN terminal of this unit to the output terminal of the central controller for custom installation system.

By connecting the REMOTE CONTROL OUT terminal of this unit to the REMOTE CONTROL IN terminal of the other component, you can also operate it with the system remote control. In this way, up to 6 components can be connected in series.

UT DVD/LD

TV/DBS

REMOTE CONTROL

ER SURROUND

IN OUT

ON SCREEN SELECTOR

BS VIDEO VIDEO

ER

VIDEO SIGNAL

13

Image 15

Contents RX-V692 RX-V592 Safety Instructions Important Notice do not Modify this Unit We Want You Listening For a Lifetime for US customers onlyFCC Information for US customers only For US customers onlyContents Speaker Configuration FeaturesFor Canadian Customers Battery replacement Dolby Pro Logic Surround + DSP Profile of this UnitDigital Sound Field Processing Dolby Pro Logic SurroundSpeaker Configuration Speaker SetupSpeaker Configuration Speaker PlacementA. model ConnectionsConnections with Other Components Output GND Video Audio OUT Video OUTGND terminal For turntable use AC* Outlets Switched6CH Discrete Output Connecting with a Dolby Digital AC-3 DecoderRX-V692 only Left Main speakers B Connecting SpeakersHow to Connect Remote Control IN, OUT terminalsCenter Output terminal Impedance Selector switchRear Surround Output terminals Main Output terminalsAM loop Connecting the AM loop antennaAntenna Connections GND terminalRX-V692 Controls and Their FunctionsTreble BassTuning DOWN/UP button Center Mode buttonVideo AUX terminals Stereo indicator Memory indicatorAuto Tuning indicator Tape Monitor indicatorSet to the OFF Speaker Balance AdjustmentFor 4 speaker configuration For 5 speaker configurationAdjust its level To turn off the power Basic OperationsProvided for RX-V692 only To Record a Source to Tape or MD Selecting the Speaker system Adjusting the Balance controlAdjusting the Bass and Treble controls Using the Tone Bypass switchTuning Operations Tuning offSelect the reception band FM or AM confirming it on Manual Preset Tuning Preset TuningTo store stations Automatic Preset TuningWhen the automatic preset tuning is finished To recall a preset stationExample Exchanging Preset StationsBrief Overview of Digital Sound Field Programs Using Digital Sound Field Processor DSPJazz Club Program Feature Concert VideoMovie Theater TV SportsTo play a source with the digital sound field processor Adjustment of the Rear Level Adjustment of the Center LevelAdjustment of Delay Time Mm MovieTheater 120 90 60 Setting the Sleep TimerTo cancel the selected Sleep time To set the Sleep timeSide panel Remote Control TransmitterBasic Operations When the lid is open Lid is openedReset button Master Volume up and down keys Sleep timer keySystem Power and OFF keys Reset buttonEmpty keys 1 Learning NEW Control Functions When the lid is openKeys which can have three functions 1, 2, 3 To use these keysUsing Operation Control Keys When the lid is closed About the marks shown on the remote control transmitterOperation To operate your VCR Except REC/PAUSE, A/B, DIR a and B+10 Switch Macro Operations When the lid is closedSetting the Macro switch Preset macro keysOn area C of keys Macro keyOn area a of keys On area B of keysLearning a NEW Function Memory back-up Making a NEW MacroTrouble shooting guide To Clear All Learned Functions Clearing Learned FunctionsTo Clear a Learned Function Troubleshooting Specifications General Seccion DE AM