Yamaha RX-V650 owner manual Connecting the antennas, Connecting the AM loop antenna, Model only

Page 23

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Indoor FM antenna

(included) AM loop antenna (included)

TUNER

75Ω UNBAL.

AM

FMGND ANT ANT

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■Connecting the AM loop antenna

1Set up the AM loop antenna, then connect it to the terminals on this unit.

CONNECTIONS

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.

■

75-ohm/300-ohm antenna adapter

PREPARATION

 

 

(U.K. model only)

 

1

Open the cover of the

 

 

included 75-ohm/300-ohm

 

 

antenna adapter.

 

2Cut the external sleeve of the

75-ohm coaxial cable and

11 mm

8 mm

prepare it for connection.

6 mm

3Cut the lead wire and

remove it.

Lead wire

4Insert the cable

wire into the slot,

Clamp

Clamp

and clamp it with

 

 

pliers.

 

 

 

Insert wire

 

 

into slot.

 

5Snap the cover into place.

2Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.

3Orient the AM loop antenna for the best reception.

■FREQUENCY STEP switch

(Asia and General models only)

Because the interstation frequency

 

 

 

spacing differs in different areas, set

FREQUENCY STEP

the FREQUENCY STEP switch

 

 

10KHZ / 100KHZ

 

 

9KHZ / 50KHZ

 

 

 

AM FM

(locating on the rear panel) according

 

 

 

to the frequency spacing in your area.

 

 

 

•North, Central and South America: 100 kHz/10 kHz

•Other areas: 50 kHz/9 kHz

Before setting this switch, disconnect this unit’s power cord from the AC wall outlet.

English

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents RX-V650 Special Instructions for U.K. Model For U.K. customersContents Other features FeaturesBuilt-in 7-channel power amplifier Sound field featuresPlease check that you received all of the following parts Supplied accessoriesInstalling batteries in the remote control Getting StartedFront panel Controls and FunctionsEurope models only Remote control Handling the remote control Using the remote controlFront panel display Presence and surround back speaker indicators 96/24 indicatorLFE indicator Input channel indicatorsVoltage Selector Rear panelAC Outlets Speaker placement Speaker Setup10 mm Connecting to Presence speaker terminalsSpeaker connections Banana plug connectionsCenter Subwoofer System Presence speakersRight Left Right Left FrontSUB Woofer jack Front terminalsCenter terminals Surround terminalsDigital jacks ConnectionsCable indications Analog jacksVideo Monitor Connecting video componentsConnections for DVD playback DVD playerFor 6-channel input Connecting to the Multi CH Input jacksUse these jacks to connect any video source, such as a Connections for other video componentsVideo AUX jacks on the front panel MD recorder or Tape deck Connecting audio componentsConnections for audio components CD playerConnecting to an external amplifier 75-ohm/300-ohm antenna adapter Connecting the antennasConnecting the AM loop antenna Frequency Step switch Asia and General models onlyMemory back-up Connecting the AC power cordImpedance Selector switch Impedance Selector switchFront panel Turning on the powerTurn on the video monitor connected to this unit Optimizer microphone position Auto SetupOptimizer microphone setup IntroductionAutomenu Starting the setupResultwiring Resultexit ErrorError E-5 If an error screen appearsPress u / d to select Result LIST, then press Select When you are finished, press SelectResultwiring screen appears If a warning screen appearsErrors during auto setup Troubleshooting for auto setup procedureBefore auto setup Select the input source Adjust the volume to the desired output levelPlayback Basic operationsTo mute the sound To listen with headphones Silent CinemaTo adjust the tone Select a sound field program if desiredPlaying video sources Background Selecting sound field programsMulti CH Input Selecting Multi CH InputDecoders select with j Remote control operationEnjoying multi-channel software Auto AutoPRO Logic SUR. Enhanced Press q/DTS on the remote control to select the decoderEnjoying 2-channel software PRO Logic SUR. StandardPress Pure Direct to activate pure direct To cancel, press Pure Direct againListening to high fidelity stereo sound Night listening modesDownmixing to 2 channels Listening to unprocessed input signalsSelecting input modes StraightPress u / d to display the following Information about the input signalDisplaying information about the input SourceAutomatic tuning TuningAutomatic and manual tuning Press FM/AM to select the FM band Presetting stationsManual tuning Automatically presetting FM stationsAutomatic preset tuning options Manually presetting stationsRepeat steps 1 to 5 to store other stations Selecting preset stationsWhen performing this operation with the remote Control, first press Tuner to set the remote toPress and hold PRESET/TUNING Edit for more than 3 seconds See Selecting preset stationsReceiving RDS stations Changing the RDS mode PTY Seek function To cancel this functionPress PTY Seek Mode to set this unit PTY Seek modeEON function Recording Special considerations when recording DTS softwareFor movie/video sources Sound Field Program DescriptionsSUR. Standard Dolby DigitalSUR. Standard Dolby Digital SUR. EnhancedSUR. Standard PRO Logic PRO LogicRock Concert For music sourcesConcert Hall Jazz ClubP08 Movie Theater Selecting the OSD mode Using the sleep timerSetting the sleep timer Advanced OperationsSleep OFF Canceling the sleep timerPress j / i to adjust the speaker output level Press Select when you have completed your adjustmentPress AMP Press Test Using the test toneOutputting the test tone from the Presence speakers Option Menu SET MenuSound Menu Input MenuTo exit, press SET Menu when finished Using SET MenuPress u / d to select Manual Setup Press Select to enter Manual SetupSurr L/R SP Sound Menu 1/2Center SP Front SPCross Over Surr B L/R SPPresence SP LFE/BASS OUTSpeaker distance CSP Distance 02ASUBWOOFER PhaseCSP Distance Gaudio SET Dcenter GEQElfe Level Fdynamic RangeOptical OUT HPR/SB SelectInput Menu CMPNT-V InputAdisplay SET Binput ModeCoaxial Option MENU1/2Parameter initialization CPARAM. INI Bmemory GuardCPARAM. INI Dzone SETControlling other components Remote Control FeaturesControl area Controlling this unitInput area Category Manufacturer Setting manufacturer codesPress Code SET using a ballpoint pen or similar object Transmit indicator on the remote control flashes twiceVCR Controlling other componentsClearing a setup manufacturer code for component control Clearing setup manufacturer codesElements of a sound field What is a sound field Changing parameter settingsEditing Sound Field Parameters Press u / d to select the parameters Resetting parameters to the factory presetsTo reset a certain parameter To reset all parametersRoom SIZE/P. Room Size Room size INIT. DLY Initial delaySound Field Parameter Descriptions Liveness Surround liveness INIT. DLY Surround initial delaySB INIT. DLY Surround back initial delay Room Size Surround room sizeREV. Level Reverberation level REV.DELAY Reverberation delayREV.TIME Reverberation time For DTS Neo6 Music Image Center image DIALG.LIFT Dialog liftFor 7ch Stereo CT Width Center widthGeneral TroubleshootingOne side can be Sound suddenlyGoes off Only the speaker onSources cannot be Or DTS indicator onVolume level Dolby Digital or DTSTuner Function properly Remote controlDoes not work nor Press Straight Effect to select the desired setting Resetting the Factory PresetsBe sure this unit is in standby mode Factory Preset appears in the front panel displayAudio formats GlossaryPCM Linear PCM Sound field programsAudio information LFE 0.1 channelVideo signal Video signal informationComponent video signal Composite video signalSpecifications Citizen Korting Cable TV Satellite TunerVCR DVD Player DVD RecorderLD Player CD PlayerTape Deck CD RecorderMD Recorder WD06180

RX-V650 specifications

The Yamaha RX-V650 is a dynamic and versatile home theater receiver that caters to audiophiles and casual listeners alike. Launched in the early 2000s, it has become a favorite for those seeking high-quality sound and a range of versatile features to enhance their audio and visual experiences.

One of the standout features of the RX-V650 is its powerful audio performance. It delivers a robust 6.1-channel surround sound system, boasting a total output power of 100 watts per channel. This capability allows it to drive a wide array of speakers, creating an immersive listening experience for music and movies. With support for a range of surround sound formats, including Dolby Digital EX and DTS-ES, the RX-V650 can effectively place the listener in the heart of the action, providing outstanding sound quality for both cinema and music playback.

In addition to its audio prowess, the RX-V650 offers a wealth of connectivity options. It includes several digital inputs, such as optical and coaxial ports, which allow for easy integration of various multimedia devices, including DVD players, gaming consoles, and streaming devices. The inclusion of component video inputs also enables high-definition video playback, making it an ideal choice for modern home theater setups.

The receiver's advanced technology features Yamaha's proprietary YPAO (Yamaha Parametric room Acoustic Optimizer), which automatically calibrates speaker settings based on the unique acoustics of the room. This not only simplifies setup but also ensures that the audio quality is tailored to the environment, enhancing the overall listening experience.

Another noteworthy characteristic of the RX-V650 is its user-friendly interface. The on-screen display allows users to navigate various settings and options seamlessly, making it easy to customize sound profiles or switch between inputs. Additionally, the remote control is designed for simplicity, providing quick access to frequently used functions.

In conclusion, the Yamaha RX-V650 stands out as a powerful and feature-rich home theater receiver. With its impressive audio performance, comprehensive connectivity options, advanced technologies like YPAO, and user-friendly interface, it remains a solid choice for anyone looking to elevate their home entertainment experience. Whether for watching movies, listening to music, or gaming, the RX-V650 presents a balanced blend of power and versatility, fulfilling the demands of a modern home theater system.
Top Page Image Contents