Yamaha RX-V559 owner manual Elfe Level, Speaker distance CSP Distance

SET MENU

■Speaker distance C)SP DISTANCE

Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations. Thus, a certain amount of delay must be applied to the sound from each speaker so that all sounds will arrive at the listening position at the same time.

■Center graphic equalizer D)CENTER GEQ

Use this feature to adjust the built-in 5-frequency band (100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic equalizer for the center channel so that the tonal quality of the center speaker matches that of the front speakers. You can make adjustments while listening to the currently selected source component or a test tone.

Control range: –6 to +6 dB

Control step: 0.5 dB

Initial setting: 0 dB

	C)SP DISTANCE		D)CENTER GEQ
.	UNIT;;;;;;;;feet
			.
;;;10.0ft
				-______+
;;;10.0ft
			;;;;;;	0dB
;;;;10.0ft
			;;;;;;	0dB
	p	p
			;;;;;;	0dB
			;;;;;;	0dB
			;;;;;;	0dB
			p	p

Unit UNIT

Choices: meters (m), feet (ft) Initial setting:

[U.S.A. and Canada models]: feet (ft)

[Other models]: meters (m)

•Select “meters” to adjust speaker distances in meters.

•Select “feet” to adjust speaker distances in feet.

Speaker distances

Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)

Control step: 0.10 m (0.5 ft)

•Select “FRONT L” to adjust the distance of the front left speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “FRONT R” to adjust the distance of the front right speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “CENTER” to adjust the distance of the center speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “SUR. L” to adjust the distance of the surround left speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “SUR. R” to adjust the distance of the surround right speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “SUR. B” to adjust the distance of the surround back speaker.

Initial setting: 2.10 m (7.0 ft)

•Select “SWFR” to adjust the distance of the subwoofer. Initial setting: 3.00 m (10.0 ft)

Note

“CENTER”, “SUR.L”, “SUR.R”, “SUR.B” and “SWFR” cannot be adjusted if “CENTER SP” (see page 79), “SUR. L/R SP” (see page 79), “SUR. B SP” (see page 79) and “LFE/BASS OUT” (see page 79) are set to “NONE” respectively.

Test tone TEST

Choices: OFF, ON

•Select “OFF” to stop test tones and output the currently selected source component.

•Select “ON” to output test tones from the front left and center speakers, and adjust the tonal quality of the center speaker.

y

Press u / d to select a frequency band and j / i to adjust the selected frequency band.

■Low-frequency effect level E)LFE LEVEL

Use this feature to adjust the output level of the LFE (low- frequency effect) channel according to the capacity of your subwoofer or headphones. The LFE channel carries low-frequency special effects which are only added to certain scenes. This setting is effective only when this unit decodes Dolby Digital or DTS signals.

Control range: –20 to 0 dB

Control step: 1 dB

E)LFE LEVEL

.;;;;;;0dB

;;;;0dB

p p

Speaker SPEAKER

Adjusts the speaker LFE level.

Headphone HEADPHONE

Adjusts the headphone LFE level.

Note

Depending on the settings of “LFE/BASS OUT” (see page 79), some signals may not be output at the SUBWOOFER OUTPUT jack.

OPERATION ADVANCED

81