Stereo Setup, Mono Setup | AudioSource AMP110, AMP102 specification

AMP102 / AMP110

OWNER’S MANUAL

APPLICATIONS

NOTE: It should be noted that the AMP102/110 is rated to operate into a minimum 8-ohm bridged load. Therefore, if you are using more than a single

8-ohm loudspeaker in bridged mode you should consider using an impedance matching speaker selector, such as the Phoenix Gold® Innovative Home ISM4, ISM6 or ISM8 or possibly using an impedance matching volume control, such as the Phoenix Gold® Innovative Home VMT100 available at your favorite DIY store or electrical supply. The choice of a volume control would allow you the additional flexibility of being able to attenuate the volume whenever necessary.

STEREO SETUP

In this conﬁguration, the mode switch is set to “Stereo”. Connect the line out jacks from a stereo preampliﬁer or source to the Line 2 input jacks of your AMP102/110 (Figure 9). Next connect your speakers to the terminals marked “Speaker A” observing proper polarity (see “Speaker Terminals” Page 6). Connect a second (optional) pair of speakers to the terminals marked “Speaker B”. Select the “A” speakers using the front panel speaker selection buttons.

Line 1	Line 2	Line 2
IN	IN	OUT

(From Pre-amp Line Out)

Figure 9. Stereo Setup

MONO SETUP

In this conﬁguration, the mode switch is set to “Bridged”. Connect the left line out from a preampliﬁer to the left Line 2 inputs of your AMP102/110. Connect your mono speaker to the terminals of your AMP102/110 (see “Speaker Terminals” on Page 6). Leave the balance set to the center detent position.

13970 SW 72nd Ave. Portland, OR 97223 • 503.914.4688 • www.audiosource.net

SETUP FOR MULTIPLE SOURCE

In the application shown in Figure 10, a distributed audio system is connected to the AMP102/110 as a local zone ampliﬁer via the Line 2 inputs. Normally the distributed audio system will be the audio source for the AMP102/110. The distributed audio is then passed on to be used by additional zones or sub zones in the distributed system via the Line 2 outputs.

Line 1	Line 2	Line 2
IN	IN	OUT
L
R

(From Local Source Line Out)

(From Pre-amp Line Out) (Out to Additional Zones)

Figure 10. Line Level with Multiple Sources

The audio output of a local source, such as an MP3 Player, CD, television, computer, etc., is connected to the AMP102/110 via the Line 1 inputs, and whenever the local source is active its signal will take priority over the distributed audio signal present at Line 2 . However, the distributed audio signal will still be present at the Line 2 input. In this circumstance the audio output of the local source will be heard via the AMP102/110. Once the local source is turned off or muted, the AMP102/110 will automatically switch back the distributed audio system as an audio source, assuming the local source remains inactive. The delay time of 4 seconds determines when switch back to the normal source will occur.

AMP110, Home Audio Multi-Zone Power Amplier, AMP102 specifications

The AudioSource AMP102 and AMP110 are exceptional home audio multi-zone power amplifiers designed to elevate your audio experience. Catering to music enthusiasts and professionals alike, these amplifiers provide extensive power and flexibility to suit various audio needs.

The AMP102 is a two-channel amplifier rated at 100 watts per channel, whereas the AMP110 boasts a significant enhancement with 110 watts per channel. Both models are engineered to drive a variety of speaker configurations, making them perfect for multi-room setups. With the ability to connect up to four separate pairs of speakers, these amplifiers ensure that you can fill your entire home with high-quality sound.

One of the standout features of the AudioSource amplifiers is their robust construction and efficient design. They utilize advanced technologies to provide clean and powerful audio reproduction, characterized by low total harmonic distortion (THD). This ensures that listeners enjoy a crisp, clear audio experience without unwanted artifacts or noise.

Both amplifiers support multiple input options, including RCA and 1/4-inch TRS inputs, allowing for seamless connectivity to various audio sources such as TVs, CD players, and streaming devices. The rear-panel input selection switch makes it easy to switch between different sources, providing added convenience for users.

The multi-zone functionality of the AMP102 and AMP110 is particularly noteworthy. Users can enjoy independent audio control in different rooms, allowing for personalized listening experiences across various spaces in the home. Each zone can be adjusted for volume independently, ensuring everyone can enjoy their preferred audio without disturbing others.

For those who value energy efficiency, both models comply with Energy Star standards, making them environmentally friendly choices. They also come with built-in protection circuitry to safeguard against short circuits, overheating, and speaker overload, prolonging the lifespan of the amplifier.

In summary, the AudioSource AMP102 and AMP110 are versatile and powerful audio amplifiers that bring high-quality sound to any home. With their multi-zone capabilities, flexible connectivity options, and robust design, they are an excellent choice for any audio setup, ensuring that users can enjoy their favorite music in any area of their home with clarity and precision. Whether you are hosting a gathering or simply enjoying a quiet evening, these amplifiers deliver an enriching audio experience that enhances any environment.