Graham Field 9000APS service manual Troubleshooting Motor Cables & Control BOX, Quick Reference

Page 28

Zenith aps seRies

TROUBLESHOOTING MOTOR CABLES & CONTROL BOX

1.HEAD, FOOT, OR HI/LO FUNCTION NOT WORKING

a.Check plugs to make sure they are firmly seated in all ports on your Control Box and are plugged into the correct ports (See diagram at right).

b.Check all cables to make sure they are not frayed, pinched, or damaged in any way. If any cable is damaged, UNPLUG YOUR BED’S POWER CORD FROM THE WALL OUTLET and REPLACE THE CABLE AND/OR THE ELECTRONIC COMPONENT.

c.HEAD DECK NOT RAISING - Unplug the power cord. Switch the head and foot plugs (ports 1 and 3). Re-plug the power cord and press the FOOT button to test.

-HEAD WORKS = Control Box head port bad. Replace box (See page 31 for order information.)

-DOESN’T WORK = Replace the Head Motor. (See page 31 for order information.)

d.FOOT AND KNEE DECKS NOT RAISING - Unplug the power cord. Switch the foot and head plugs (ports 3 and 1). Re-plug the power cord and press the HEAD button to test.

-FOOT WORKS = Control Box foot port bad. Replace box (See page 31 for order information.)

-DOESN’T WORK = Replace the Foot Motor. (See page 31 for order information.)

e.BED DOES NOT GO UP AND DOWN IN HORIZONTAL POSITION - If you press the Up or Down Hi/Lo button and you hear a click or buzz but nothing happens = Check your Hi/Lo Motors by touching them & pushing the Hi/Lo buttons.

POWER PLUG

BATTERY

HB 4 3 2 1

T-CABLE

FOOT HILO

FOOT

HEAD HILO

HEAD

2. BED LOOKS UNLEVEL - HILO MOTORS ARE NOT IN SYNC.

a. Press the Hi/Lo “DOWN” button repeatedly on either the Staff Control or Pendant/Hand Controller until the bed goes completely down and rests in its full horizontal position. The two HI/LO motor shafts should be completely retracted inside the motors.

-YOU FEEL NOTHING = possible bad motor - go to the third step below.

-YOU FEEL SLIGHT VIBRATION = Motor OK.

-Unplug the Power Cord = Switch the two Hi/Lo plugs (ports 4 and 2) in the Control Box. Re-plug the power cord and press the same Hi/Lo button, then touch the same non-vibrating motor.

i.MOTOR NOW VIBRATES = Bad port in the Control Box - Replace box. (See page 31 for order information.)

ii.MOTOR DOES NOT VIBRATE = Replace

the bad Hi/lo Motor. (See page 31.)

Basic American Medical Products, a division of GF Health Products, Inc.

QUICK REFERENCE

-HI/LO & FOOT WORKS, BUT HEAD DOES NOT: Switch Head & Foot Motor Cable at the Control Box and test (See Step C in left column).

-HI/LO & HEAD WORKS, BUT FOOT DOES NOT: Switch Foot & Head Motor Cable at the Control Box and test (See Step D in left column).

-HEAD & FOOT WORKS, BUT HI/LO DOES NOT:

a.Switch Head and Foot Hi/Lo Motor Cables at the Control Box and test (See Step E in left column).

b.Test to see if Hi/Lo Motors need to be re-aligned (See Step F above).

 

 

 

 

 

28

 

www.grahamfield.com

999-0831-190A Service Manual

Image 28
Contents Instructions for USE Important Notice Basic American Medical ProductsZenith aps seRies Important Safety and Warning Information Operating ConditionsTypical APS 9000 BED Identification Labels With Grounded Electrical CableTypical SAFETY/WARNING BED Labels Entrapment & Compliance Information Zenith 9000 APS Mechanics Zenith 9000 APS ElectricalUnpacking Your BED Discard KeepHEAD- and Footboard Assembly Headboard InstallationFootboard Installation HeadboardPlugging in the Footboard NURSE/STAFF Control Attaching the FootboardStandard Mattress Retainer Installation Head Retainer InstallationFOOT-END Retainer Installation Retainer PositionsStandard Wireform Wallsaver Installation Wallsaver AssemblyWallsaver RemovalBracket Installation Wallsaver RemovalBED Operations APS PENDANT/HAND Controller Backlit PendantBED Operations NURSE/STAFF Control Panel Lock OUT Single FunctionsBED Operations Chair Position BED Operations CPR/HEART PositionHead END Foot END751/1%5 BED Operations TRENDELENBERG/REVERSE TrendelenbergAPS 9000 Series Electrical Components Linak OptionalBattery Backup Cable Ground Wire APS9000 Series Electrical Cabling StandardAPS9000 Series Electrical Cabling with Underbed Light Underbed Light Cable UBLMounted Battery Option Optional Pivot Assist BAR Installation & Operation Pivoting Assist BAR OperationOptional Trapeze Support Installation  Optional Battery Backup Replacement Configurations Troubleshooting Staff Control Blinking Lights Troubleshooting Nothing Works no PowerNothing Works no Power Troubleshooting Pendant & Double T-CABLE Nothing on Staff Control Works but Pendant WorksStaff Control Works but Pendant Hand Controller Function DOESN’TTroubleshooting Motor Cables & Control BOX HEAD, FOOT, or HI/LO Function not WorkingBED Looks Unlevel Hilo Motors are not in Sync Quick ReferenceTROUBLESHOOTING/REPLACING Your APS Staff Control Removing and Replacing the Staff Control AssemblyRecommended Maintenance and Inspection Electrical Inspection of Control Box 6 monthsSERVICE/REPLACEMENT Part Record Double T-CABLE SERVICE/REPLACEMENT Part Diagram Electronics SERVICE/REPLACEMENT Part Diagram Decking SERVICE/REPLACEMENT Part Diagram Main Frame Capping Capping on Arms & Legs Zenith aps seRies GF121699RevA12

9000APS specifications

The Graham Field 9000APS is a remarkable piece of medical equipment designed specifically for healthcare facilities and home care environments. This innovative product showcases the company's commitment to quality, functionality, and user-centric design in assistive technology.

One of the standout features of the 9000APS is its advanced mobility solution, making it an ideal choice for patients with limited mobility or those recovering from surgery. The chair is equipped with a lightweight aluminum frame that contributes to its overall robustness while ensuring ease of transport and maneuverability. The strong yet manageable design supports a wide range of user needs, offering both stability and comfort.

The 9000APS features an ergonomic design that prioritizes the user's comfort. It is outfitted with contoured seating and soft padded armrests, which provide a supportive experience during prolonged use. The chair's adjustable height feature further enhances comfort and accessibility, allowing caregivers to tailor the chair to meet specific needs, especially when transferring patients from different surfaces.

Additionally, this model includes a dual-action braking system that enhances safety. The brakes can be easily engaged by the caregiver, preventing any unintentional movement while the patient is seated. Safety is also indicative in the chair’s non-slip feet, which ensure that it remains stable on various floor surfaces, further promoting user confidence.

In terms of technology, the Graham Field 9000APS emphasizes ease of use. Its compact and foldable design makes it simple to store and transport. The integrated storage compartments provide caregivers with quick access to personal items or essential medical supplies, streamlining the overall care process.

The chair is also designed with hygiene in mind. The materials used are easy to clean and maintain, which is crucial in preventing infections and ensuring a sanitary environment for patients. The fabric is not only durable but also resistant to moisture and stains, making it ideal for various healthcare settings.

Overall, the Graham Field 9000APS combines comfort, safety, and practicality, making it an exceptional choice for both patients and caregivers. Its innovative features and thoughtful design underscore Graham Field’s commitment to improving the quality of life for individuals requiring mobility assistance, ultimately making it a valuable addition to any healthcare routine.