Pentax 40 MZ-3i operating instructions Special functions, Pull-out/push-in wide-angle diffuser

Page 26

13. The zoom reflector

Wide angle diffuser

Pull-out/push-in wide-angle diffuser

 

Pull out the wide-angle diffuser

under the main reflector, all the way to the

front. Then release it. This causes the main reflector to automatically advance to zoom position 20 mm. The wide-angle diffuser automatically folds up, and the distances and zoom value on the LC display are modified accordingly.

To push in the wide-angle diffuser, press on the left and right-hand guide rails of the black guide plate. The wide-angle diffuser will fold down and can then be pushed in completely.

14. Special functions

 

Exposure o.k.

 

 

 

 

 

 

 

 

 

 

Fig. 26: Exposure o.k.

 

The correct exposure indicator („o.k.“)

lights up only when the frame will be,

or was, correctly exposed in the auto and TTL mode.

In this manner it is possible to manually trigger a test flash while in auto mode so that the correct aperture can be established beforehand. This is particularly valuable with bounced flash when reflection conditions are difficult to judge.

1 The test flash is triggered with the manual firing button

(fig. 26).

If the exposure o.k. indicator

remains dark after the test flash was fired, then

adjust the next larger aperture (smaller f-number) or diminish the distance to the reflection surface or subject, and repeat the test flash.

The f-stop established in this manner must also be set on the camera.

To trigger a test flash, hold the camera and flashgun in the same manner as for the actual shot.

This facility can also be used with TTL mode without having to produce test expo- sures. The flashgun is adjusted to auto mode, and the correct aperture is then determined with a test flash in the previously described manner. The established aperture is transferred to the camera, and the flashgun is then readjusted to TTL mode.

This procedure is relatively accurate with lenses of medium focal length of between 28 mm and 85 mm. But in borderline cases underexposure may occur with subsequent TTL exposure.

46

47

Image 26
Contents Mecablitz 40 MZ-3i Sensor Main switch LC display lighting / Modelling lightNomenclature LC display Acoustic exposure verification on Film speedContents Brief survey of the operating functions ForewordPlease also open the back cover page with the illustrations Stroboscopic mode, ch , pSafety Instructions Never fire a flash in the immediate vicinity of the eyesPreparations Battery warning indicatorClose the battery compartment cover Removing the Standard Foot or SCA adapter Switching the flashgun on and offMounting the flashgun on the camera Mounting the Standard Foot or SCA adapterDirect way to good flash shots TTL flash modeSetting procedure for TTL mode Easy Mode Automatic flash modeSetting procedure for TTL Easy Mode To EM„ + or „ button See ch , p Setting procedure for auto flash modeTo a Also be set on the camera lensManual flash mode Setting procedure for manual flash modeBounce flash Lock-in positions of reflector and headBouncing the flash in the auto and TTL modes Bouncing the flash in the manual modeMounting the light reducing filter With secondary reflectorTTL remote operation Setting procedure for Metz TTL remote operationMetz cordless TTL remote operation ControllerSwitching off the Metz TTL remote operation Checking the slave addressRemote-Operation Setting procedure for Metz a remote operationMetz cordless auto remote operation Distance values on the LC display disappearUsing the winder in auto and TTL modes Winder modeUsing the winder in the manual mode Setting procedure for manual mode with partial light output Partial light output levels in the auto modePartial light output levels in the manual mode Flash durations Stroboscopic modeWorking with partial light output levels Macrophotography close-upsSetting procedure for stroboscopic mode Use the „+ or „- buttonFill-in flash in daylight Fill-in flash in auto modeFill-in flash in manual mode Complete illumination of shadow areasFill-in flash in TTL mode Working with user programsProg. flashes Procedure for storing a programCalling a stored program Zoom reflector main reflector Setting procedure for the Ex-Zoom modeZoom reflector Ex-Zoom-modePull-out/push-in wide-angle diffuser Or was, correctly exposed in the auto and TTL modeSpecial functions AF measuring beam AF measuring beamML function Modelling Light ML-functionsSwitching on with the controls locked An intermittent beep signalling alarm soundsSwitching on the „Beep function Locking the controls key functionTesting the display segments Calling the Service ModeAdjusting the dimensional units Rapid functionExposure corrections in TTL mode Technical DataExposure corrections in auto mode Exposure correctionsRemarks ModeFreq. fHz 105Example ProcedureFlashes per second = fHz Partial light output PIncluded Optional extras Flashing operating mode symbols Troubleshooting hintsNo display in on switch position Meaningless informationAlphabetical index Fill-in flash