Matrox Electronic Systems 10760-101-0200 manual Lut

Page 31

Matrox Meteor-II /Camera Link grab section 31

Optotrig

Userinput1

TTLtrig

Opto-

TTL

coupler

buffers

On a separate

bracket (PCI)

DB-9

TTLtrig

TTL buffer

trigger

Optotrig

Opto-

connector

coupler

LVDStrig

LVDS

User input0

receivers

User input1

Hsync output_1

Hsync output_2

Vsync output_1

Vsync output_2

Clock output_1

Clock output_2

LVDS

CC1_1

DB-44

CC1_2

drivers

connector

CC2_1

CC2_2

CC3_1

CC3_2

CC4_1

CC4_2

TTLCamCtrl(3)

TTL

TTLCC1

TTLCC2

buffers

TTLVSOUT

TTLHSOUT

CC1

CC2

LVDS

CC3

drivers

First

CC4

DATA (24)

Channel

MDR-26

& syncs (4)

Link # 1

connector

Clock

receiver

SerTFG

LVDS driver

SerTC

& receiver

CC1

CC2

LVDS

CC3

drivers

Second

CC4

DATA (24)

Channel

MDR-26

& syncs (4)

Link # 2

connector

Clock

receiver

SerTFG

LVDS driver

SerTC

& receiver

Userinput0	LVDStrig	Clockoutput 1	Clockoutput 2	Vsyncoutput 2	Hsyncoutput 1	Hsyncoutput 2
LVDS				LVDS
receivers				LVDS
receivers			drivers
			drivers
			PSG

UART

For PC/104-Plusform factor

Auxiliary sync and control connector

Interfaces to DB44 connector of Matrox 4Sight-II chassis

VM Channel (PCI only)


LUT			32
4 256x8-bit			32
4 256x8-bit
2 1Kx10-bit
2 4Kx12-bit

			VIA


			64


Video transfer						32
	memory
	(32 MB)

Host 32-bit PCI bus

Image 31

Contents Matrox Meteor-II /Camera Link Page Contents Hardware reference Appendix B Technical information Page Introduction TTL Matrox Meteor-II /Camera LinkOr Matrox Genesis processor board1 Processing, analysis, and archiving Matrix/bar code reading, and calibrationAcquisition, transfer, display control, and archiving MIL-LiteInspecting the Matrox Meteor-II /Camera Link package What you need to get startedTo your computer and all peripherals Installation overview Introduction Hardware Installation Installing Matrox Meteor-II /Camera Link Screw Metal Plate BIT PCI Board Slot Hardware installation VMChannel. Used to send data to another Matrox board Connecting external devicesMatrox Meteor-II /Camera Link for PC/104-Plus Reference manual for pinout information Connectors pinoutHardware installation Installing software Installing the software Using multiple Matrox Meteor-II Boards Grabbing simultaneously from different boards Multiple board installationGrabbing from two Matrox Meteor-II boards Using multiple Matrox Meteor-II boards Hardware reference Matrox Meteor-II /Camera Link grab section Matrox Meteor-II /Camera Link hardware referenceLUT Max Board are as followsThree ways Each of the video input Camera Link connectorsSection earlier in this chapter Is specified by the DCFVideo Interface Asic Data interfacesPCI interface Hardware reference Appendix a Troubleshooting Common problems and solutions TroubleshootingNot enough memory to allocate buffer under Windows NT IRQ conflicts Contacting Matrox Appendix a Troubleshooting Appendix B Technical Information Technical information Connector pinouts for Matrox Meteor-II /Camera Link for PCI PIN Signal Pinout for the two Camera Link connectors is as followsSame type and length Medium Configuration Pin SignalHDT44P Pin Signal Description Pinout of the 9-pin DB9 female connector is as followsTop view of board Dgnd DATA4 DATA5 DATA6 DATA7 DATA8 DATA9 Extender board Specifications Min. of 6.3 mA recommended Max. of 10 mA recommended Environmental Appendix B Technical information Appendix C Glossary Asic DCF See also progressive scanning Also known as non-interlaced. See also interlaced scanning See also horizontal sync Index Uart EU Notice European Union Regulatory ComplianceFCC Compliance Statement Industry Canada Compliance StatementPage Dorval, Quebec H9P 2T4 Product supportPage Product Assistance Request Form Describe the problem