Vivotek IP7142 manual Network deployment, Ethernet switch

Page 8

VIVOTEK - A Leading Provider of Multimedia Communication Solutions

Network deployment

Setup the Network Camera over the Internet

This section explains how to conﬁgure the Network Camera to Internet connection.

1.If you have external devices such as sensors and alarms, make connection from general I/O terminal block.

2.Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch. Use Catagory 5 Cross Cable when Network Camera is directly connected to PC.

3. Connect the power cable from the Network Camera to a power outlet.

1

12

	1	2
	1	Ethernet switch
		Ethernet switch

N.C.: No Connector

485B: RS485-

485A: RS485+

AC24V: Power in AC 24V

AC24V: Power in AC 24V

GND: Ground

DI : Digital Input

DO : Digital Output

+12V : Power, 12V DC

3

There are several ways to setup the Network Camera over the Internet. The ﬁrst way is to setup the Network Camera behind a router. The second way is to utilize a static IP. The third way is to use PPPoE.

Internet connection via a router

Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below.

1.Connect your Network Camera behind a router, the Internet environment is illustrated as below. About how to get your IP address, please refer to Software installation on page 10 for details.

WAN (Wide Area Network )

IP address : 192.168.0.3

Subnet mask : 255.255.255.0

Internet

Router IP address : from ISP

Default router : 192.168.0.1

LAN (Local Area Network)

Router IP address : 192.168.0.1

Cable or DSL Modem

IP address : 192.168.0.2

Subnet mask : 255.255.255.0

Default router : 192.168.0.1

8 - User's Manual

Image 8

Contents Page Table of Contents Package contents Read before useConnectors Physical descriptionDI/DO Diagram Hardware installation Hardware ResetWall mount Ceiling mount Ethernet switch Network deploymentInternet connection with static IP Set up the Network Camera through Power over Ethernet PoE Software installation Accessing the Network Camera Using web browsersPage Using Rtsp players Using 3GPP-compatible mobile devices Using Vivotek recording software Main Live Video Window Video title itle and ti e Client Settings MP4 Saving Options System Time SystemSystem DI and do Root Password SecurityAdd User Manage UserEnable Https Create and Install CertiﬁcateTo create a self-signed certificate Certificate Information Network Network TypePPPoE Point-to-point over Ethernet Page Http Https Two way audioFTP Rtsp Streaming Page Ddns Dynamic domain name service DdnsCustomSafe100 Delete allowed list / Delete denied list Access listAllowed list / Denied list Video settings Audio and videoImage Settings Privacy mask Page Page Audio settings To enable motion detection, follow the steps below Motion detectionEr enta e RS485 Settings Camera controlPreset Position Custom CommandNetwork Camera Media Settings ApplicationNaps ot Server Settings Page Page Event Settings Page Recording Settings RecordingPage Current Log System logRemote Log View parameters Restore MaintenanceReboot Calibrate Upload / Export Daylight Saving Time Conﬁguration FileUpgrade Firmware Rti Er d Style convention URL Commands of the Network CameraOverview General CGI URL syntax and parameters Security levelGet server parameter values Method GET/POSTSet server parameter values Page Available parameters on the server Timezoneindex 489 ~ Group dii0~ndi-1 Group doi0~ndo-1Group security Subgroup of network httpSubgroup of network pppoe Subgroup of network httpsSubgroup of network rtsp Group ipfilter Page Page Adjust saturation of image according to mode settings Group upnppresentation Group upnpportforwarding= Logalert = Logcrit Even Group uarti0~n-1 n is uart port countGroup capability Group eventi0~2 Group serveri0~4 Group mediai0~4 Group recordingi0~1To enable or disable this recoding Drive the digital output Query status of the digital inputQuery status of the digital output Capture single snapshotAccount management Upgrade ﬁrmware System logsSystem Information Method PostIP ﬁltering Method GET/POSTSenddata Get SDP of StreamingsOpen the network streamings Page Technical Speciﬁcations LensTechnology License Notice Electromagnetic Compatibility EMC