Vivotek IP7142 manual Physical description, Connectors

Page 4

VIVOTEK - A Leading Provider of Multimedia Communication Solutions

Physical description

Front panel

Light sensor

Lens

IR LED

Connectors

General I/O terminal block

Ethernet 10/100 RJ45 plug

Audio out (green)

Microphone in (pink)

Power cord socket (black)

Earth

General I/O Terminal Block

This Network Camera provides a general I/O terminal block which is used to connect external input / output devices. The pin deﬁnitions are described below.

N.C.

485B

485A

AC24V

AC24V

N

2V

N.C.: No Connector

485B: RS485-

485A: RS485+

AC24V: Power in AC 24V

AC24V: Power in AC 24V

GND: Ground

DI : Digital Input

DO : Digital Output

+12V : Power, 12V DC

Pin	Name	Specification
N.C.	No Connector
485B	RS485-	3.3V
485A	RS485+	3.3V
AC24V	Power in AC 24V	AC 24V ± 5%
AC24V	Power in AC 24V	AC 24V ± 5%
GND	Ground
DI	Digital Iutput	OPEN/Short-to-GND, isolation 2kV
DO	Digital Output	Max. 40VDC, max. 400mA, isolation 2kV
+12V	Power +12V	12VDC ± 10%, max. 0.4A

4 - User's Manual

Image 4

Contents Page Table of Contents Package contents Read before useConnectors Physical descriptionDI/DO Diagram Hardware installation Hardware ResetWall mount Ceiling mount Ethernet switch Network deploymentInternet connection with static IP Set up the Network Camera through Power over Ethernet PoE Software installation Accessing the Network Camera Using web browsersPage Using Rtsp players Using 3GPP-compatible mobile devices Using Vivotek recording software Main Live Video Window Video title itle and ti e Client Settings MP4 Saving Options System SystemSystem Time DI and do Root Password SecurityAdd User Manage UserEnable Https Create and Install CertiﬁcateTo create a self-signed certificate Certificate Information Network Network TypePPPoE Point-to-point over Ethernet Page Http Https Two way audioFTP Rtsp Streaming Page Ddns Dynamic domain name service DdnsCustomSafe100 Allowed list / Denied list Access listDelete allowed list / Delete denied list Video settings Audio and videoImage Settings Privacy mask Page Page Audio settings To enable motion detection, follow the steps below Motion detectionEr enta e RS485 Settings Camera controlPreset Position Custom CommandNetwork Camera Media Settings ApplicationNaps ot Server Settings Page Page Event Settings Page Recording Settings RecordingPage Remote Log System logCurrent Log View parameters Reboot MaintenanceRestore Calibrate Upload / Export Daylight Saving Time Conﬁguration FileUpgrade Firmware Rti Er d Overview URL Commands of the Network CameraStyle convention General CGI URL syntax and parameters Security levelGet server parameter values Method GET/POSTSet server parameter values Page Available parameters on the server Timezoneindex 489 ~ Group dii0~ndi-1 Group doi0~ndo-1Group security Subgroup of network httpSubgroup of network rtsp Subgroup of network httpsSubgroup of network pppoe Group ipfilter Page Page Adjust saturation of image according to mode settings Group upnppresentation Group upnpportforwarding= Logalert = Logcrit Even Group uarti0~n-1 n is uart port countGroup capability Group eventi0~2 Group serveri0~4 Group mediai0~4 Group recordingi0~1To enable or disable this recoding Drive the digital output Query status of the digital inputQuery status of the digital output Capture single snapshotAccount management Upgrade ﬁrmware System logsSystem Information Method PostIP ﬁltering Method GET/POSTOpen the network streamings Get SDP of StreamingsSenddata Page Technical Speciﬁcations LensTechnology License Notice Electromagnetic Compatibility EMC