AGFA DC-530i user manual Troubleshooting, Problem Cause Solution

Page 55

computer. It may be unable to playback the data using the digital camera.

Troubleshooting

Problem

Cause

Solution

Power does not turn on.

Battery is inserted in the

Reload battery in the correct

 

wrong direction.

direction.

 

 

 

 

Batteries are dead.

Replace or recharge batteries.

 

 

 

 

The battery compartment

Make sure the battery

 

door is open.

compartment door is securely

 

 

closed.

 

 

 

The camera does not take

The flash is charging.

Wait for the flash to charge.

pictures.

 

 

Memory is full.

Insert a new memory card.

 

 

 

 

Memory card is not

The card may be defective,

 

formatted correctly.

use a new card.

 

 

 

Image is not recorded when

The Flash is charge.

Wait for the flash to charge.

the shutter button is

 

 

Memory is full.

Insert a new memory card.

pressed.

 

 

 

 

 

The flash does not fire

Flash is set to OFF.

Set the flash to any mode

 

 

except off.

 

 

 

Image is blurry or out of

The camera was moving

Hold the camera steady when

focus.

when the image was

shooting picture.

 

captured.

 

 

 

 

 

The subject was beyond

Turn the Macro mode on it the

 

the range within which the

subject is within 15 cm (zoom

 

camera can focus.

out) or 40 cm (zoom in).

 

 

Do not use Macro mode when

 

 

shooting distant subjects.

 

 

 

Image is not displayed on

A memory card with

This camera cannot display

the LCD monitor.

non-DCIF images (recorded

non-DCIF images.

 

with other camera) is

 

 

loaded.

 

 

 

 

Recorded images are not

The camera was turned

If the battery low indicator

saved in memory.

off/powered down before

appears on the LCD monitor,

 

the image was stored in

replace the battery

 

memory

immediately.

 

 

 

Cannot transfer images to a

USB driver is not installed.

Install the USB driver before

computer after connecting

 

you connect the camera to a

 

 

 

 

 

50

Image 55
Contents DC-530i Extending battery life Precautions„ FCC Compliance and Advisory Iii ContentsMaking Connections Getting Started Using This MenuAttaching the Wrist Strap Scope of deliveryParts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries About Camera Memory Inserting the Memory CardInsert the card TipsSetting the Display Language Setting the Display Language / Date & TimeSetting the Date & Time Apply the setting REC mode Using the LCD MonitorDpof Play mode„ Play mode „ REC modeChanging the LCD Status Basic Operation Turning the Power On and OffPress the Power button n again to turn the power off Power Saving FunctionSet the camera to the REC mode Launch the mode palette Changing the ModeSwitching between REC mode and Play mode Selecting the REC modePage Select an item Using the MenusChange the setting REC menuPress the Menu n button to close the menu Setup menuOpen the Setup menu REC menu list MovieOff Setup menu listReset BeepComputer / Printer PALNiMH Take a picture Basic RecordingRecording Still Images Half press the shutter button to focus the imageUsing the Q mode Resolution Values Setting the Resolution and QualityQuality Values Recording Movie Clips Setting the Movie SizeUsing the Zoom Function Using the Flash Using the Macro Burst Using the Self-timer & Burst10 sec DoublePress the shutter button again to end recording Recording and Playing VoicesRecording Audio Clips Playing Back Audio ClipsPress the SET button to start recording for 30 seconds Adding a Voice MemoRecording a Voice Memo Open the Play menuSetting the White Balance Setting the MeteringOther Recording Functions Setting the Highlight Setting the ISOSetting the Exposure Setting the AEBSetting the Photo Effect Setting the SharpnessSetting Date Stamp Press the four-way control or n Turn the power on, and set the camera to the Play modePlayback Playing Back ImagesSave the image Magnifying & Trimming Still ImagesMagnify the image Trim the imagePlaying a Slide Show Change the slide show settingsViewing in Thumbnail Button to show the selected image in full screenPlaying the slide show Deleting FilesDeleting a Single File Delete images Deleting Multiple FilesPress or to select Select, and then press the SET button Select multiple imagesProtecting a Single File Play mode Open the menuProtecting All Files Thumbnail screen Open the menu Press or to select Lock all, and then press the SET buttonPress the SET button to protect all images Protecting Multiple FilesChanging the Image Size Editing ImagesRotating Still Images Press the SET button to rotate the imageChanging the Image with Effects Copying the FilesS3 Press or to select Single, then press the SET button Setting the DpofPrint the date stamp out Choosing a Startup Image Making Connections Connecting the Camera to a TVDisplay on TV Using the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable Double-click the Removable Disk icon to view its contents Software InstallationSystem Requirements Utilities Drivers Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Install VideoStudio 7 SE VCD Drive. The autorun menu appears Installing the Software Driver Installing Ulead Photo Explorer 8 SE Basic Follow the on-screen instructions to install the driversUsing the Software Installing VideoStudio 7 SE VCDUlead Photo Explorer 8 SE Basic File Naming AppendixAbout the Folder & File Name Folder StructureProblem Cause Solution TroubleshootingFunction Available List Mode FunctionStill Capture Ntsc / PAL SpecificationsManufactured by plawa-feinwerktechnik GmbH & Co. KG Customer careDeclaration of Conformity