Arcam AVR600 manual AMP Device Mode, IPod commands, OK selects/play the highlighted file

���AMP Device Mode

The ADevice Mode button configures the CR102 to control the AVR600. Pressing this button does not affect the currently selected input on the AVR600.

IMPORTANT: The CR102 must also be in AMP Device

Mode to control the following sources: PHONO, MCH (multi-channel analogue), AUX, NET (optional network audio), USB, IPOD (for use with the optional Arcam rLead or rDock).

However to control the internal Tuner (AM/FM/DAB or Sirius if fitted) the CR102 must first be inTun Device Mode (see later).

The functionality of the CR102 is context sensitive for the internal sources and is described in the following table.

PSingle press – Toggles AVR600 power between standby and on in the current zone (zone in which the command is received). Press and hold – Forces all AVR600 zones into standby, regardless of which zone the command was received in.

0…9	The number keys can be used for source
	selection (without changing the CR102
	Device Mode). Alternatively the Device
	Mode buttons can also be used with the
	SHIFT key.
	0SAT (satellite) input
	1PHONO input
	2AV input
	3TUNER input
	4DVD input
	5TAPE input
	6VCR input
	7CD input
	8AUX (front panel) input
	9MCH (multichannel) input
PHONO	Selects Tape input on the AVR600

EAVR600SHIFT + Eselects Phono input on the

RPT (for iPod and NET sources)

R

SModifies many keys (see individual key descriptions below).

AUX Selects MCH (multichannel) input on the

HAVR600

SHIFT + Hselects AUX input on the AVR600

NET Selects iPOD input on the AVR600

ESHIFT + E selects network (net) internal input on the AVR600

	Navigate menus
��	OK confirms a setting (equivalent to ‘Enter’
	or ‘Select’ on some remote controls)

Press and hold OK to force the analogue and digital video outputs to the default resolution: 480i (525-line NTSC).

Shift + <decreases the picture resolution. Shift + >increases the picture resolution. Shift + 'turns current zone (in which command is received) on

Shift + ,turns current zone (in which command is received) off.

MCycles through the available surround and downmix modes.

UDisplays the AVR600 setup menu on the On Screen Display (see page 34).

DCycles through the front panel display’s brightness options

@Toggles the mute function of the AVR600

] [ (track control for iPod and NET sources)
	SHIFT + [Follow Zone1 source.
	When the command is received in Zone2
	or Zone3, the source for that zone follows
	whatever input source is selected in Zone1
- +	Decrease (–) and increase (+) AVR600
	volume
DIRECT	Stereo direct on/off. Provides a direct
)	analogue path from the analogue inputs to
	the left and right front outputs. Switches off
	any surround processing modes and shuts
	down the DSP circuits for the best stereo
	sound quality.
EQ	Displays the room EQ settings menu
$
EFFECT	(for iPod and NET sources)
&
BASS	Calls up a pop-up (and front screen) to
(	adjust the bass setting for a particular input.
Trim	Brings up the speaker trim menu.

!Use the B, C, D and E navigation buttons. Press TRIM again to exit the speaker trim menu.

As this is a temporary adjustment, these additional trim levels are reset to zero when the unit is turned off or the selected input is changed, but are retained if the unit is put into standby. These temporary trim levels are independent of the speaker levels found in the setup menu.

sync Delays may be introduced into the video

#signal by video processing which causes a mismatch between the audio and video timing. You will notice this by speech sound being out of synchronization with the lip movements in the video.

To compensate for this, you can adjust the lip sync delay. Press the sync button and use the D and E navigation buttons. Press again to exit the lip sync trim menu.

SUB Brings up the subwoofer trim menu. Use

%the D and E navigation buttons. Press Sub again to exit the sub trim menu

TREBLE Calls up a pop-up (and front screen) to

Hadjustinput. the treble setting for a particular

FAV+	(for iPod and NET sources)
U
FAV-	(for iPod and NET sources)
T
HOME	(for iPod and NET sources)
O
INFO	Cycles through the information displayed

Bon the lower left portion of the front panel display.

iPod commands

The iPod interface is selected by pressing E in AMP Device Mode on the CR102. When connected to an iPod via an optional rLead/rDock, the keys below are used to navigate music files in AMP Device Mode.

Navigate the files on screen.

��	OK selects/play the highlighted file.
RPT	Toggles random (shuffle) play of the playlist

Ron and off.

SHIFT + Rcycles through the repeat options

] [	Selects the previous/next track in the
	current playlist
$	Begins or resumes playback at the currently
	highlighted track

&Togglestrack pause and playback of the current

#Stops playback

E-26