Arcam AVR600 Video Inputs, Video Outputs, Important points to remember, For analogue outputs

Page 40

Video Inputs

Settings to optionally assign a video source to each of the normally audio-only inputs.

These settings are stored in memory and recalled each time the unit is powered up.

Video Input Tape –

Video Input CD –

Video Input Aux –

Video Input AM / FM –

Video Input Phono –

Video Input MCH –

Video Input iPod –

Video Input Net –

Video In Digital Radio –

The default for each of the audio inputs is ‘None’, however for example you could associate the satellite ‘Sat’ video with AM, FM and Digital Radio audio if you wished. This way you could listen to the FM or AM or Digital Radio commentary of a sports game but have the pictures from the satellite coverage.

Video Outputs

The settings in this menu control the output resolution from the video processor in the AVR600 as well as the operation of the two HDMI outputs.

These settings are applied to all video inputs and are stored in memory and recalled each time the unit is powered up.

NOTE

Important points to remember:

For analogue outputs

The analogue output resolution should be chosen carefully; Composite and S-Video connections can only carry 480i (525-line NTSC) or 576i (625-line PAL) signals. If an output resolution higher than this is chosen in Out 1 Resolution, the Composite and S-Video main zone outputs will be disabled.

You should also set the frame rate (50Hz Interlaced for PAL, 60Hz Interlaced for NTSC) and the aspect ratio (4:3 standard or 16:9 widescreen) to match your display device. Note that S-Video and Composite can only carry Interlaced video. If you select Progressive analogue video, Zone 1 S-Video and Composite outputs will be disabled.

For HDMI outputs

The output resolution, frame rate and display aspect ratio can be automatically determined by the AVR600. Alternatively these settings can be manually selected. If you have two HDMI display devices connected, you can also configure which of the two HDMI outputs takes priority.

Zone 1 OSD – Selects whether the main zone pop-up OSD messages are On or Off. It is stored in memory and recalled each time the unit is powered up.

<When On, all user adjustments that are made during the general use of the AVR600 are displayed on screen as well as the front panel display. This includes the adjustment of volume, subwoofer level, lip sync, tone controls, etc. It is stored in memory and recalled each time the unit is powered up.

<When Off, the above user adjustments will not appear on screen, only on the front panel display. This leaves the picture on your display device clear of pop-up text. However, regardless of this setting the Setup menus are always displayed on screen.

Analogue Output – This setting controls the output resolution of the analogue video outputs of Zone 1. This applies to all Zone 1 analogue video outputs:

Component, S-Video and Composite. This setting is only valid if neither of the HDMI outputs Out 1 or Out 2 are being used at the time. See ‘Important points to remember’ above regarding analogue resolutions.

The dropdown list shows all the resolutions that the AVR600 video processor can output.

Analogue Frame Rate – This setting controls the output frame rate of the analogue video outputs of Zone 1. This applies to all Zone 1 analogue video outputs: Component, S-Video and Composite. This setting is only valid if neither of the HDMI outputs Out 1 or Out 2 are being used at the time. See the Note ‘Important points to remember’ regarding analogue frame rates.

Display Type – Set the aspect ratio of your display device; 4:3 standard or 16:9 widescreen.

Output Switching – This setting controls the operation of the two HDMI outputs.

<Auto-Priority Out 1/Out 2 senses which display device is turned on and gives priority to the named output (Out 1 or Out 2) if both display devices are on at the same time. When both display devices are on at the same time, the output with the highest priority is used to configure the settings of the AVR600 video processor.

<Output 1 or Output 2: forces only the named HDMI output to be enabled.

<Output 1 & 2: enables both HDMI outputs simultaneously. In order to do this however, the settings of the AVR600 video processor are reduced down to the highest common set that can be supported by both display devices.

Out 1 Resolution – This setting controls the output resolution of HDMI output Out 1. This setting is only valid if HDMI output Out 1 is the only active HDMI output at the time.

<The dropdown list shows all the resolutions that the AVR600 video processor can output. Resolutions that are not supported by the connected display device are greyed out and cannot be selected.

<Preferred: sets the Out 1 resolution to be the preferred resolution that is requested by the display device. This is often the highest resolution the display device can receive.

Out 1 Frame Rate – This setting controls the output frame rate of HDMI output Out 1. This setting is only

valid if HDMI output Out 1 is the only active HDMI output at the time.

<The dropdown list shows all the frame rates that the AVR600 video processor can output. Frame rates that are not supported by the connected display device at the above resolution are greyed out and cannot be selected.

<Auto sets the Out 1 frame rate to be the preferred frame rate that is requested by the display device for the currently used resolution.

Lipsync 1 – (Information only) Displays how much lip sync is automatically applied to HDMI output Out 1 to compensate for video processing delays in the attached display device. Not all display devices support this function.

Out 2 Resolution – This setting controls the output resolution of HDMI output Out 2. This setting is only valid if HDMI output Out 2 is the only active HDMI output at the time.

<The dropdown list shows all the resolutions that the AVR600 video processor can output. Resolutions that are not supported by the connected display device are greyed out and cannot be selected.

<Preferred: sets the Out 2 resolution to be the preferred resolution that is requested by the display device. This is often the highest resolution the display device can receive.

Out 2 Frame Rate – This setting controls the output frame rate of HDMI output Out 2. This setting is only valid if HDMI output Out 2 is the only active HDMI output at the time.

<The dropdown list shows all the frame rates that the AVR600 video processor can output. Frame rates that are not supported by the connected display device at the above resolution are greyed out and cannot be selected.

<Auto: sets the Out 2 frame rate to be the preferred frame rate that is requested by the display device for the currently used resolution.

Lipsync 2 – (Information only) Displays how much lip sync is automatically applied to HDMI output Out 2 to compensate for video processing delays in the attached display device. Not all display devices support this function.

E-38

Page 39 Page 41
Image 40
Page 39 Page 41
Contents AVR600 N d b o o k AVR surround amplifierSafety Guidelines Important safety instructionsSafety compliance Class II productInstructions de sécurité importantes Class II produitRespect des consignes de sécurité Page Contents Professional Installation?DIY setup? WelcomeBefore you Begin… Power Standby powerPlacing the unit Interconnect cablesTrademark acknowledgements Video connectors Digital connectorsAudio connectors Power inletHdmi connectors GeneralMaking connections Component/RGB Video CompositeZone 3 connectors Zone 2 connectorsDigital audio connectors Connect the Component video outputs of your sourcePhono Analogue audio Front panel AUX input MCH input InputsAnalogue record outputs Front panel Phones socketEnglish DVD player Satellite receiverCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Aerial connectors Radio ConnectorsSirius Connecting an aerial Other Connectors Data connectors Network connectors USB connectorRS232 serial connector RLead/rDockInfra-red IR connectors English Trigger connectorsRoom Connecting subwoofers Speaker cables Connecting speakersSpeakers Centre SubwooferFront left and right Surround left and rightSwitching on OperationOperating your AVR600 Selecting a sourceUsing Zone 2 Updating firmware using a PCRestore to factory defaults Extended front panel menuFront panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backIPod commands AMP Device ModeOK selects/play the highlighted file TUN Device Mode DVD Device ModeNetwork commands Highlighted menu on the screenAV Device Mode SAT Device ModeMenus PVR Device Mode VCR Device ModeCD Device Mode English Essential Setup Speaker typesSpeaker Distances Speaker LevelsAuto speaker Setup ProblemsUsing a subwoofer Very strong acoustic resonances within the roomSetup menus Navigating the setup menuInput Config Treble BassPlii Dimension Plii Centre Width Plii Panorama General SetupGeneral information and system controls Auto Setup Spkr TypesSpkr Distance Spkr LevelsVideo Inputs Video OutputsImportant points to remember For analogue outputsZone Settings ModeNetwork For Stereo sourcesIntroduction Decoding ModesTwo-channel source modes High resolution audio sources Multi-channel source modesDecoding modes For Dolby Digital sourcesSettings Volume LevellerDolby Volume is a sophisticated new Calibration OffsetEnglish Tuning/Channel Selection Saving and selecting PresetsDeleting Presets Tuner OperationSirius errors Default unlock code isOperation Locking ChannelsNetwork/usb Operation Selecting the playback sourceUSB playback Internet radio stationsExternal Amplifiers SW2, SW3Multi-room Set up ZoneZone 2 and 3 control outputs Audio outputsZone English Customising CR102 Code LearningCreating Macros Volume punch-throughKey Mover Mode Mover Locking/Unlocking a specific Device ModeTo restore a moved Device Mode key to its original state Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Volume is always too loud When I turn onSwitched off Wired networkSpecifications Continual improvement policyProduct Guarantee Worldwide GuaranteeClaims under guarantee Problems?Device code Tables HCM ICEIRT ITCRFT SBRSEG SEIAVP GPXKEC KLHADB NTLUPC DKKCAT CGVDCE ENGAsci SKY+TPS UECYES SH215E Issue 4301-7333+0
Related manuals
Manual 74 pages 35.94 Kb Manual 74 pages 48.95 Kb Manual 68 pages 17.1 Kb

AVR600 specifications

The Arcam AVR600 is a high-performance AV receiver that is designed for audiophiles and home cinema enthusiasts who seek a premium audio and video experience. This receiver stands out with its array of features and technologies that elevate sound quality and user experience.

At the heart of the AVR600 is its high-fidelity amplification system. The receiver is equipped with a robust 7-channel amplification setup, delivering a total output of 120 watts per channel into 8 ohms. This power enables the AVR600 to reproduce dynamic audio with precision, whether it be for movies, music, or gaming. The class G amplifier design offers exceptional efficiency and reduces distortion, ensuring that sound remains clean and focused even at higher volumes.

The AVR600 boasts extensive connectivity options to accommodate various audio and video sources. It features multiple HDMI inputs and outputs supporting 3D video and 4K scaling, providing flexibility for connecting modern devices. The unit also includes analog and digital inputs, a dedicated phono input for vinyl enthusiasts, and support for multi-room audio setups. With its built-in Bluetooth and network streaming capabilities, users can easily access high-resolution audio files from their digital libraries or popular streaming services.

One of the key technologies in the AVR600 is its advanced room correction system, known as Dirac Live. This sophisticated calibration tool analyzes the acoustics of the room and automatically adjusts the output of the receiver to compensate for any sound anomalies. As a result, listeners experience optimized sound tailored to their specific environment, enhancing the overall listening experience.

For video performance, the AVR600 supports a range of formats, including Dolby Atmos and DTS:X, ensuring an immersive home theater experience with enveloping surround sound. It also features advanced video processing capabilities, allowing users to upscale standard-definition and high-definition content to near 4K quality, further enhancing picture clarity.

In terms of user interface, the AVR600 provides an intuitive on-screen display and a well-designed remote control that makes navigating through settings and options seamless. The receiver is also compatible with smartphone apps for additional convenience, allowing users to control playback and settings directly from their mobile devices.

Overall, the Arcam AVR600 is a versatile audio-visual receiver that combines power, connectivity, and advanced technologies to create an exceptional home entertainment experience. Its unique blend of performance and flexibility makes it an excellent choice for those looking to invest in high-quality audio and video solutions for their homes.
Top Page Image Contents