JVC GR-AX860 specifications Check Your Work, Release Animation Mode

Page 33
START TIME-LAPSE RECORDING
5 Press RECORDING START/STOP. Recording and intervals alternate automatically.
RELEASE TIME-LAPSE MODE
6 To release when the tally lamp is not blinking, press INT. TIME and REC TIME repeatedly until “ ” and “ ” disappear. To release when the tally lamp is blinking, press RECORDING START/STOP to stop the blinking, then press INT. TIME and REC TIME repeatedly until “ ” and “ ” disappear, or set “Interval Timer” and “Rec Time” in the Sub Menu screen to “OFF”.
•You can also set the interval time in the Sub Menu screen. Press “–” to move the highlight bar down to “Interval Time”, press NEAR, and press + or – to cycle through the choices.
•Exposure control (☞ pg. 20), manual focusing (☞ pg. 23) and D.I.S. settings
(☞ pg. 20) should be performed at this point. Once you perform step 5, these settings cannot be changed.
SET INTERVAL BETWEEN RECORDINGS
4 Press INT. TIME on the remote control. There are five choices available, and they appear in the following order (each time INT. TIME is pressed): OFF, 15S, 30S, 1 min, and 5 min. Press again to reset.
•You can also set the recording time in the Sub Menu screen. Press “–” to move the highlight bar down to “Rec Time”, and press NEAR, then press + or – to cycle through the choices.
SET RECORDING TIME
Set SP/LP to SP (☞ pg. 11).
SET RECORDING SPEED
Make sure the lens cover is open, then set the power switch to “CAMERA”.
1
2
3 Press REC TIME on the remote control. There are four choices available, and they appear in the following order (each time REC TIME is pressed): 1/4S, 1/2S, 1S, and 5S. Press again to reset.
ENGAGE RECORD–STANDBY MODE
You can record sequentially at preset time spans. Leaving the camcorder aimed at a specific subject, you can record subtle changes over an extended period of time.
Time-Lapse
ASSEMBLE SERIES OF PICTURES
START RECORDING
4 Press RECORDING START/STOP after focusing on the subject. The recording stops automatically after the selected period of time.
•You can also set the recording time in the Sub Menu screen (☞ pg. 32). Press “–” to move the highlight bar down to “Rec Time”, press NEAR, and press + or – to cycle through the choices. Then press MENU.
SET RECORDING TIME
3 Press REC TIME on the remote control. Four choices are available, and they appear in the following order (each time REC TIME is pressed): 1/4S (one-fourth of a second), 1/2S (one-half of a second), 1S (one full second) and 5S (five seconds). Press again to release the Animation mode.
SET RECORDING SPEED
Make sure the lens cover is open, then set the power switch to “CAMERA”.
1
2 Set SP/LP to SP (☞ pg. 11).
ENGAGE RECORD–STANDBY MODE
Give stationary scenes or objects an illusion of movement. This function allows you to shoot a series of pictures, each slightly different, of the same object for a brief period of time.
Animation
33

5 Repeat steps 3 and 4 for the desired number of pictures.

CHECK YOUR WORK

6 Play back the series of pictures to see if the results were satisfactory.

RELEASE ANIMATION MODE

7 Press REC TIME until “” disappears from the viewfinder, or set “Rec Time” in the Sub Menu screen to “OFF”.

NOTES:

●For best results, make sure the camcorder is secured when shooting in Animation or Time-Lapse mode.

●Fade-in/out cannot be performed during Animation or Time-Lapse shooting.

●Before performing other operations following Animation or Time-Lapse recording, make sure the Animation or Time-Lapse mode is deactivated.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents GR-AX860 Dear Customer Connection to the mains supply in the United KingdomCrossed Out Dust Bin Mark Some DO’S and DON’TS on the Safe USE of Equipment Remote Control Cassette Adapter Battery Pack Ajor FeaturesCorner Wipe CR2025 Shoulder StrapEject BATT. ReleasePush 3PLAY/PAUSE 2REW StopSupply Power PowerAttach Battery Pack Detach Battery PackDC OUT Clock Battery Lithium Insertion/Removal Viewfinder AdjustmentGetting Started Date/Time Setting Tape Length Setting SET Tape LengthPress + or to move the highlight bar to Tape Length Loading/Unloading a Cassette Recording Mode SettingOpen Cassette Holder INSERT/REMOVE CassetteGrip Adjustment Shoulder Strap AttachmentTripod Mounting Installing The Battery Using The RM-V706U Remote Control UnitPull OUT Battery Holder Replace Battery HolderCording Basic Recording Enter RECORD-STANDBY ModeLoad a Cassette Start ShootingFAR + Menu FeaturePurpose OperationRetake Auto Pause START/STOP VissVideo Light SET Video LightLight ON/AUTO/OFF Choose Display Mode Ecording Advanced FeaturesDate/Time Insert DisplaySnap Shot Snap Shot Mode Select Snapshot ModeSnapshot Perform Snapshot RecordingExposure Control Digital Image StabilizerAdjust Focus White Balance AdjustmentAdjust White Balance White balance mode indicatorLock Focus FocusingRelease Focus Lock FAR NearPower zoom lever Release Manual Focus ModeSelect Effect Programme AE With Special EffectsDeactivate Effect EFFECT/PROG.AE OFFCinema-like 169 wide-screen effect Change the settingPicture becomes sepia-tinted reddish brown monochrome Creating the look of an old photographStart Recording Reserve EffectEND Recording FADE/WIPEAuto Select DissolveMake Setting Using Menu For Detailed AdjustmentChange Settings Select Function AT SUB MenuJlip ID no Select Preset Title Access Instant Title Menu Screen Display Preset Title Instant TitlesEND Character Setting Access Character SET MenuInput Characters + Menu FAR NearNear FAR Menu RecordingTally lamp START/STOP INT. Time REC TimeCheck Your Work Release Animation ModeInsert Cassette in Adapter Cassette AdapterPlay Back on Connected VCR Remove Cassette from AdapterConnection To a VCR a Connectors B Playback onlyEditing, Dubbing and Playback Connect Camcorder to TVPlayba CK Basic Playback PLAY/PAUSE Stop REW PowerRewind or Fast-forward the tape PlaybackTracking PLAY/PAUSE Counter R/M REW Stop Pause Play Playback FeaturesRandom Assemble Editing R.A.Edit Power switchEdit PLAY/PAUSE On NextSET Remote to Operate VCR Connect the editing cable to the R.A. Edit connectorOperate the VCR Connect toEditin G Begin Automatic Editing Engage VCR’S RECORD-PAUSE ModeEND Automatic Editing Edited Tape VCR Edit StopIndicator Counter R/MREW Play Insert Pause External Mike Audio dubbing indicator ViewfindereREW Play DUBAfter Use Cleaning The CamcorderSymptom On again. If the error number still appears Review or Retake modeTroubleshootin G Viewfinder, consult your nearest JVC dealerIndex Tally Lamp Power On Indicator Video Light Microphone Jlip Joint Level Interface Protocol ConnectorQW E R T External MIC jackPack’s remaining power level Changes as follows according to the batteryWhen the power is Almost gone, the indicator blinks, then the unitIndex Terms Serious malfunctioning Do not us e near flammable or explosive materialsSpecial Notes on Video Heads Detection, timer Adjustment Auto/Manual adjustmentControlled Dimensions X 42 H Weight Approx g Dimensions X 25 H Weight Approx g AccessoryMemo Memo GR-AX860
Top Page Image Contents