JVC GR-D90 GR-D70 instruction manual To DV @ Core filter, DV cable Optional Core filter To DV

Page 34

Dubbing To Or From A Video Unit

Equipped With A DV Connector

(Digital Dubbing)

It is also possible to copy recorded scenes from this camcorder onto another video unit equipped with a DV connector. Since a digital signal is sent, there is little if any image or sound deterioration.

To Use This Camcorder As A Player

1 Make sure all units are turned off. Connect this camcorder to a video unit equipped with a DV input connector using a DV cable as shown in the illustration.

2 Set this camcorder’s VIDEO/MEMORY Switch 4 to “VIDEO”, then the Power Switch u to “PLAY” while pressing down the Lock Button y located on the switch, turn on the video unit’s power, and insert the appropriate cassettes in this camcorder and the video unit.

3 Press 4 7 to play back the source tape.

4 While watching the playback on the monitor, engage the DV connector-equipped video unit’s record mode from the spot on the source tape you want to begin recording.

NOTES:

●It is recommended to use the AC Adapter as the power supply instead of the battery pack ( pg. 7).

●If the remote control is used when both the player and recorder are JVC video units, both units will perform the same operation. To prevent this from happening, press the buttons on both units.

●If a blank portion or disturbed image is played back on the player during dubbing, the dubbing may stop so that an unusual image is not dubbed.

●Even though the DV cable is connected correctly, sometimes the image may not appear in step 4. If this occurs, turn off the power and make connections again.

●If “Playback Zoom” ( pg. 14, 35), “Playback Special Effects” ( pg. 35) or “Snapshot” is attempted during

playback, only the original playback image recorded on the tape is output from the DV connector @.

●When using a DV cable, be sure to use the optional JVC VC-VDV204U DV cable.

To Use This Camcorder As A Recorder

1.Set this camcorder’s VIDEO/MEMORY Switch 4 to “VIDEO”, then the Power Switch u to “PLAY” while pressing down the Lock Button y located on the switch.

2.Set “REC MODE” to “SP” or “LP” in the Menu Screen ( pg. 31).

3.Connect the DV cable as shown in the illustration and load a cassette to record on.

4.Press the Recording Start/Stop button e to engage the Record-Pause mode. “ DV. IN ” appears on the screen.

5.Press the Recording Start/Stop button e to start recording. 3 rotates.

6.Press the Recording Start/Stop button e again to engage the Record-Pause mode. 3 stops rotating.

NOTES:

●Digital Dubbing is performed in the sound mode recorded

on the original tape, regardless of the current “SOUND MODE” setting ( pg. 28).

●During Digital Dubbing, incoming signals cannot be output through the video or audio connectors if they are copy-guarded.

47 e

To DV @

 

Core filter

y

OFF (CHARGE)

 

PLAY

DV cable

 

(optional)

u

 

Core filter

To DV

IN/OUT

Video unit equipped with DV connector

EN

34 DUBBING

Page 33 Page 35
Image 34
Page 33 Page 35
Contents GR-D90 GR-D70 Contents Safety Precautions Before recording an important scene Make sure the arrow is Pointing upward Wind once StopperSub Menu Using the Battery Pack PowerCharging the Battery Pack Using AC PowerLithium-ion is vulnerable in colder temperatures Grip AdjustmentViewfinder Adjustment About BatteriesTripod Mounting Approximate recording time Tape Recording modeShoulder Strap Attachment Loading/Unloading a CassetteRecording Mode Setting Date/Time SettingsScreen closes Label Clipped edge Memory card Loading a Memory Card Picture Quality/Image Size SettingTo Unload a Memory Card DisplayBasic Recording To Adjust The Brightness Of The DisplayTape Recording Journalistic Shooting Operation ModePower-Linked Operation Self-RecordingRecording from the Middle of a Tape To Control The Speaker VolumeTime Code Normal PlaybackPress Blank Search To cancel Blank Search midwayBlank Search Tape PlaybackIf using a VCR . . . go to step If not . . . go to step ConnectionsTo Remove The Shutter Sound Basic Shooting SnapshotTo Delete Unwanted Still Images To Protect Valuable Files available only for SD Memory CardMultiMediaCard Approximate Number of Storable ImagesTo Magnify The Stored Images Index Playback Viewing File InformationAuto Playback Removing On-Screen DisplayProtecting Files Deleting Files Advanced FeaturesTo Remove Protection Dubbing Still Images Recorded On a Tape To a Memory Card Setting Print Information Dpof SettingTo Reset The Setting To Print ALL Still Images ONE Print for EachMaking a New Folder To Reset The No. Of PrintsInitialising a Memory Card Folder and File namesNight-Scope Programme AE With Special EffectsFade/Wipe Effects Snapshot Recording Snapshot Mode SelectionSnapshot For Tape Recording Auto FocusTo Return To Automatic Exposure Control Manual FocusExposure Control To Brighten The Subject QuicklyIris Lock White Balance AdjustmentManual White Balance Operation Exposure WIPE/FADERProgram AE BalanceManual System Camera DisplayFor Playback Menu DSCVideo Display Video DisplayPlayback Sound Bright , DATE/TIME , Time CodeTo Use This Camcorder As a Recorder Dubbing To Or From a VCRTo Use This Camcorder As a Player DubbingTo DV @ Core filter DV cable Optional Core filter To DVFrame-By-Frame Playback Using the Remote Control UnitSlow-Motion Playback Playback Special EffectsInsert Editing Set 12bit Mode to Sound 2 or MIX Menu Screen  pgAudio Dubbing To hear the dubbed sound during playbackSET REMOTE/VCR Code Random Assemble Editing R.A.EditMake Connections Select Scenes For More Accurate Editing Adjustment of VCR/CAMCORDER TimingAutomatic Editing to VCR Diagnosing VCR/CAMCORDER TimingUsing USB cable Using USB cableUsing DV cable Connection To a Personal ComputerSnapshot mode cannot be used No power is suppliedFocus does not adjust automatically Image taken using Snapshot is too darkWhite Balance cannot be activated Black & White Fader does not workImage looks like the shutter speed is too Slow Date/time does not appearAn error indication E03 or E04 appears Charger indicator on the camcorder does Not lightAn error indication E01, E02 or E06 appears Memory card cannot be played backCassettes Battery PacksMemory Cards LCD Monitor How to handle a CD-ROMMain Unit After Use For Your MaintenanceCleaning The Camcorder About moisture condensationCamcorder AC AdapterIndex Controls, Connectors And IndicatorsRemote Control LCD monitor pg @ Digital Video Input/Output ConnectorPower Switch Audio/Video Input/OutputDuring Memory Card Recording Only LCD Monitor/Viewfinder Indications2b i t / SOUND1 1024 During Both Tape And Memory Card RecordingDisplays the sound mode for approx seconds after Appears when in the Squeeze or Cinema modeAppears when the Insert Editing w or Insert Editing Appears when Digital Image Stabiliser DIS isHigh E03 or E04 Unit in Safeguard Mode Eject E01, E02 or E06 Unit in Safeguard ModeAppears if a file in another format is selected Using The Optional RM-V717U Remote Control Unit RM-V717U optionalTerms See previous page as well
Top Page Image Contents