JVC GR-DVM5 Pull OUT Viewfinder or Open LCD Monitor, Start Recording, Stop Recording

Page 19

1 SELECT OPERATION MODE

Set the Power Dial to “ A ” while pressing down the lock button located on the dial.

2 PULL OUT VIEWFINDER OR OPEN LCD MONITOR

Pull out the viewfinder fully or open the LCD monitor to approx. 90 degrees.

•The lens cover opens, the power lamp comes on and the scene you’re aimed at appears.

•The Record-Standby mode is engaged.

3 START RECORDING

When “PAUSE” appears, press START/STOP. A beep signals the start of recording and the tally lamp comes on.

4 STOP RECORDING

Press START/STOP again to stop recording.

•The camcorder re-enters Record-Standby mode.

5 END RECORDING

When you’re finished recording, push back the viewfinder or close the LCD monitor until it clicks; the lens cover closes and the power lamp goes out.

•When transporting, make sure the viewfinder is pushed back and the LCD monitor is closed and locked.

•To turn power on again, pull out the viewfinder or open the LCD monitor.

OR

Set the Power Dial to “OFF”.

•When turning to “OFF”, it is not necessary to press down the lock button.

EN19

NOTES:

The image will not appear simultaneously in the LCD monitor and the viewfinder. No image appears on the LCD monitor when the viewfinder is pulled out. It is not possible to shoot using both LCD monitor and viewfinder.

If 5 minutes elapse in the Record-Standby mode, power shuts off automatically to conserve energy and protect the heads. To turn the camcorder on again, push back and pull out the viewfinder again or close and re-open the LCD monitor. As long as you don’t take out the tape you were using or play it back, you can continue from where you left off with no noticeable break on the recorded video.

When a blank portion is left between recorded scenes on the tape, the time code is interrupted and errors may occur when editing the tape.

Continue recording from where you stop so there

are no gaps by following “Recording from the middle of a tape” (pg. 20).

Record-Standby means that a tape is loaded and the camcorder is ready to record.

During recording, sound is not heard from the speaker. If you want to hear the sound, connect optional headphones to the headphones jack. The sound volume at this point is the same as the level it was adjusted during playback.

To make the indications disappear, press and hold the IND.ON/OFF button for more than approx. 1 second. However, it is impossible to remove the

tape running indicator “ 444” and warning indications and so on (pg. 81).

Use the viewfinder when under direct sunlight or when reflections make it difficult to see the LCD monitor.

When the battery remaining power indicator

appears as , that means the battery power is close to nil. When the battery power is exhausted, power turns off automatically.

Image 19
Contents GR-DVM5 It is recommended that you Dear CustomerConnection to the mains supply in the United Kingdom This unit is produced to comply with Standard IEC Publ Some DO’S and DON’TS on the Safe USE of EquipmentSafety Precautions Video Area Audio Area Sub-Code AreaITI Insert and Tracking Information Area RCA plug 4 RCA plug Ø3.5 mini-plug 4RCA plug Video cable DC cordGrip/Hand strap VIDEO/AUDIO cableRM-V712U Min DVM-30 Lithium battery CR2025DV30ME Charging The Battery Pack Close Battery Cover Installing The Battery PackOpen Battery Cover Insert Charged BatteryIndoor Use Using The Battery HolderLCD monitor Date/Time SettingsSelect Operation Mode Input Date and TimeTo protect valuable recordings Loading/Unloading a CassetteOpen Cassette Cover INSERT/REMOVE TapeSelect Dial Recording Mode SettingSET Recording Mode Set depending on your preferenceAttach Grip Strap to SUB Hand Strap Eyelet Adjust LengthGrip Strap Attachment Attach Grip Strap to Hand Strap EyeletTurn on Camcorder Dioptre AdjustmentAdjust Dioptre Tripod MountingInsert Battery in Holder Remote Control UnitInstalling The Battery Pull OUT Battery HolderFunction Operation ModePower Dial Position Self-Timer Playback PlayIND. ON/OFF button Display EN RecordingStop Recording Record-Standby mode is engagedPull OUT Viewfinder or Open LCD Monitor Start RecordingStart Search Engage Still ModePower lamp comes on Recording From The Middle Of a TapeDuring shooting When blank portion is recorded on a tapeTime Code Proper recordingLCD Monitor/Viewfinder Indications Tape Remaining IndicatorAdjust Brightness Brightness ControlTilt LCD Monitor Journalistic shootingInterface Shooting Open LCD MonitorZoom EN RecordingSelect Function Displaying The Date And Time During RecordingMenu button IND. ON/OFF button Select Dial END 5-SECOND Mode Recording Engage 5S ModeScene 5-second recording END SELF-TIMER Recording Self-TimerEngage SELF-TIMER Mode Stop SELF-TIMER RecordingTake Snapshot Access System MenuSelect Snapshot Mode SnapshotSnapshot mode Pin-Up mode With frame Motor Drive modePlease refer to pages 31, 32 for details MenusClose Recording Menu Recording Menu allows you to set these functionsWide Mode REC Mode Recording modeDIS Digital Image Stabilizer Zoom Zoom magnificationClose System Menu System MenuSee pages 28 Photo ModeFADE/WIPE Effects Accessmenu Manual Mode ItemAccess FADER/WIPE Menu To Cancel FADE/WIPE EffectsWH , BK , , B W Fades and WipesExample WH Fader White Example Wipe ScrollResume Recording Picture Wipe/DissolveP and P of the Fader/Wipe Menu Random Variations Fade out from colour to black and white Fade in or out with a white screenFade in or out with a black screen Fade in or out with a full-screen mosaic effectFader and Wipe Menu AE/Effects Disable P.AE/EFFECTPress START/STOP. The image begins with the selected effect Slow Slow Shutter To Change To Auto Focus Manual Focus AdjustmentAccess Manual Focus Adjust FocusTo Return To Automatic Exposure Control Adjust ExposureExposure Control Brightness control of the displayIris After , adjust the exposure rotatingIris Lock To Return To Automatic Iris ControlTo Return To Automatic White Balance White Balance AdjustmentAccessment White Balance Adjust Closement White Balance AdjustTo Change The Tint For Recording Enter SettingExit Manual White Balance Adjustment Manual White Balance OperationEND Playback Volume switchRewind Tape Viewing RecordingPress 2 or 3after pressing 6/4. The tape To Perform High-Speed SearchHigh-Speed Search. This is not a malfunction END Zoom Playback ZoomActivate Zoom Locatescene Portion of MagnifiedPlayback Effects Accessmenu Playback Effect SelectPlayback Menu allows you to set the following functions Access Playback MenuPlayback Menu Close MenuDisplaying the Date During Playback Playback SoundDisplaying The Time Code During Playback Turn on Power VCR/TV Connection when connecting directly to the camcorderSelect TV’S Video Mode Attach and Lock VCR/TV Connection using AC Charger StationBasic Connections VCR/TV connection using the AC Charger StationConnect as shown in the illustration 1, 2 or 3 pg Connect AC Charger Station to TV or VCRDigital Printer Connection To a Video Unit Equipped With a DV ConnectorConnector To DVWhile pressing down the lock Supply PowerPlug the AC Charger Station’s power cord into an AC outlet Attach Camcorder to AC Charger StationRecording deck DubbingMake Connections Start Playback Pause RecordingMake Connections Digital DubbingOperate VCR Brand SettingPg 65, or control the VCR using Remote control, you must set the VCR brandExecute FADE/WIPE in if Necessary Random Assemble EditingSET EDIT-OUT Point SET EDIT-IN PointUSE P.AE/EFFECT if Necessary Start Editing Engagemode Vcrs RECORD-PAUSEStop Editing Random Assemble Editing Menu appears For More Accurate EditingPrepare for R.A. Edit Play Back Dubbed Scene Choose a SceneInput Correction Data Adjustment of VCR‘s against Camcorder TimingPause During Dubbing Audio DubbingFind EDIT-IN Point Begin DubbingRecording Sound Display Output Sound Troubleshooting Mode recording Pg , there is a delay Snapshot mode cannot be used Digital Zoom doesn’t workVideo mode Selected Mode pgTroubleshooting Whitish LCD monitor. When This happens, the displayedWhen the LCD monitors Fluorescent light reaches Angle of the LCD monitorPlease consult your nearest LCD monitor Certain FADE/WIPE, P.AE Indications blinkLCD monitor or Camcorder’s functions Two or three timesCleaning The Camcorder Camcorder Viewfinder pg Power dial pgVolume switch Volume pg Zoom switch T/W pgAC Charger Station Function LCD Monitor/Viewfinder Indications During RecordingLCD Monitor/Viewfinder Indications During Playback Indications Function Store cassettes To prolong service lifeTo avoid hazard During useDo not leave the unit For safety, do notAvoid using the unit Dirty heads can cause the following problemsVideo GeneralAudio Audio ConnectorsOutput power VideoOn-screen display Colour temperatureAC Charger Station Auto focusIris Iris Lock LCD monitor/Viewfinder Indications Pg , 54Pg 35, 41, 51 Pg , 42GR-DVM5
Related manuals
Manual 72 pages 48.55 Kb Manual 92 pages 30.15 Kb Manual 12 pages 31.53 Kb