JVC GR-SXM607, GR-FX12, GR-SX22, GR-SX202, GR-SXM57 For Insert Editing and Audio Dubbing

Page 39

Display

 

e

4

Audio dubbing

M– 0 : 0 5 : 2 0

indicator

During Audio

Dubbing

Remote sensor

Microphone

START/STOP

REW

PLAY

PAUSE

A.DUB

STOP

RM-V715U OR RM-V700U (optional)

EN39

Audio Dubbing

You can record a new soundtrack on a prerecorded tape. The existing original sound is erased and replaced by the sound from the built-in microphone.

Perform steps 1, 2 and 3 of the Insert Editing procedure (pg. 38) before continuing.

NOTE:

Use the remote control unit to perform the following procedures.

1 Press REW to go a little beyond the beginning of the scene onto which you want to dub the new audio, press PLAY to view the recorded tape, then press PAUSE at exactly the point where dubbing should start.

2 Press and hold A. DUB, and without releasing

A. DUB, press and release PAUSE. The Audio Dub- Standby mode is engaged.

3 To begin Audio Dubbing, press PLAY. When the counter reaches “0:00:00”, Audio Dubbing stops automatically and the camcorder enters the Audio Dub-Standby mode.

4 To end Audio Dubbing, press STOP.

NOTES:

Do not press FF or REW during Audio Dub-Standby, or the edit points will not be accurate.

If the microphone is too close to the TV, or if the TV’s volume is too high, whistling or howling may occur.

NOTES

(for Insert Editing and Audio Dubbing):

Insert Editing and Audio Dubbing may not work correctly if the tape contains blank segments, or if the recording speed was changed during the original recording.

To edit/dub onto a tape, make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape.

Do not press STOP during Insert Editing or Audio Dubbing, or the edit points will not be accurate.

During Insert Editing and Audio Dubbing, when Insert-Pause or Audio Dub-Standby is engaged, the counter may go slightly past “0:00:00”. Recording, however, stops at exactly 0:00:00.

Image 39
Contents Instructions It is recommended that you Dear CustomerModels equipped with LCD monitor only GR-FXM37/FX12 only Crossed Out Dust Bin MarkAC Adapter AP-V10EG Power Cord Battery PackCore Filter x How To Attach The Lens Cap How To Attach The Core FilterSlide Battery Release and pull out the battery pack Charging the Battery PackPower To Detach The Battery PackApproximate recording time unit min Using the Battery PackUsing AC Power Perform of Charging the Battery Pack pgShoulder Strap Attachment Grip AdjustmentViewfinder Adjustment Tripod MountingComes on Date/Time SettingsPower lamp Video Out Setting French model only10 EN Recording Format SettingRegular VHS VCR RecordingPlaybackTape Length Setting Recording Mode SettingLoading/Unloading a Cassette Rotate Bright until the bright level 14 ENShooting While Watching To Stop RecordingJournalistic Shooting models equipped with LCD monitor only SELF-RECORDINGmodels equipped with LCD monitor only16 EN ZoomZoom Out Press the Recording Start/Stop Button to start recording Make sure the recording mode is set to SP5Sec. Rec 5-sec. Recording Video LightIf you press during Recording 18 ENNight 50X* GR-SXM57 only If you press during Record-StandbyFades in/out to a black screen Fade/Wipe EffectsProgram AE With Special Effects 20 ENDigital Effects If you select Jlip ID no Using Menus For Detailed AdjustmentMenu Screen Explanations Camera MenuSystem Menu System Menu 24 ENInstant Titles Date/Time InsertSet REC Time and 2 of Animation above Time-LapseExposure Control Set the Power Switch to Press MENU. The Menu Screen appearsManual Focus Focusing28 EN Auto FocusTo Change The Tint For Recording White Balance AdjustmentManual White Balance Operation Press Menu again to close the Menu Screen30 EN Load a tape pg Set the Power Switch toTo cancel the effect, select OFF in step Playback image Activate the TBC mode and Auto TrackingUse the provided Cable Adapter If your TV/VCR has a 21-pin connector32 EN GR-SXM607/SXM57/SXM47/SX202/SX22Power supply instead of the battery pack pg Basic ConnectionsTape Dubbing Slide the latch to open the adapter compartment 34 ENCassette Adapter optional CoverFunctions Buttons EN35Installing The Batteries RM-V715U, provided Installing The Battery RM-V700U, optionalWith the RM-V700U Animation Playback ZoomAnimation and Time-Lapse To End ZoomInsert Editing Use the remote control unit to perform this procedureFor Insert Editing and Audio Dubbing Audio DubbingSET REMOTE/VCR Code VCR Recording deckYou are now ready to try Random Assemble Editing Connect the editing cable to the R.A.EDIT connector Make ConnectionsConnect the editing cable to the Remote Pause terminal REW Play IN/OUT Select ScenesEditing cable and the A/V cable Automatic Editing to VCRDate/Time SettingsCharging time varies according to the ambient temperature 44 ENTime Base TBC indicator turns green grey with a camcorder equippedRecording TBCAnimation or Time-Lapse is not No power is suppliedRecording cannot be performed Recording does not startLens CAP warning indicator An error number i.e. E03 appearsThat Date/Time setting is carried out Lens CAP warning indicator may blink when3 4 5 y u # $ % 48ENDioptre Adjustment Control Video Light Switch Light OFF/AUTO/ONSpeaker Volume Control VOL Power Switch OFFIndications During Recording 50 ENRewind/Shuttle Search Pause Audio Dubbing Tape Counter Tape Running Indicator PlaybackIndications During Playback Indications FunctionTo avoid hazard To prevent damage and prolong service life52 EN Use only the following batteriesStore cassettes For safety, do notAvoid using the unit During useAbout moisture condensation To prolong service lifeCleaning The Camcorder To prevent damage to the LCD monitor, do notOnly ConnectorsOptional Accessories GeneralGR-FX12GR-FXM37GR-SX22GR-SX202GR-SXM47GR-SXM57GR-SXM607