JVC GR-DVX90 specifications 10 EN, Loading/Unloading a Cassette, Cassette holder cover

Page 10

10 EN

Cassette holder cover

Cassette holder

Make sure the window side is facing out.

PUSH HERE

OPEN/EJECT Switch

Erase protection tab*

*To Protect Valuable Recordings . . .

.... slide the erase protection tab on the back of

the tape in the direction of “SAVE”. This prevents the tape from being recorded over. To record on this tape, slide the tab back to “REC” before loading it.

GETTING STARTED (cont.)

Loading/Unloading A Cassette

The camcorder needs to be powered up to load or eject a cassette.

1 Slide down and hold OPEN/EJECT in the direction of the arrow then pull the cassette holder cover open until it locks. The cassette holder opens automati- cally.

•Do not touch internal components.

2 Insert or remove a tape and press “PUSH HERE” to close the cassette holder.

•Once the cassette holder is closed, it recedes automatically. Wait until it recedes completely before closing the cassette holder cover.

•When the battery’s charge is low, you may not be able to close the cassette holder cover. Do not apply force. Replace the battery with a fully charged one before continuing.

3 Close the cassette holder cover firmly until it locks into place.

Approximate recording time

Tape

Recording mode

 

 

 

SP

LP

 

 

 

30 min.

30 min.

45 min.

 

 

 

60 min.

60 min.

90 min.

 

 

 

80 min.

80 min.

120 min.

 

 

 

NOTES:

It takes a few seconds for the cassette holder to open. Do not apply force.

If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the cassette holder still does not open, turn the camcorder off then on again.

If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later, insert it again.

When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the cassette holder cover.

Closing the cassette holder cover before the cassette holder comes out may cause damage to the camcorder.

Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder is closed with the camcorder switched off, however, it may not recede. It is recommended to turn the power on before loading or unloading.

When resuming recording, once you open the cassette holder cover a blank portion will be recorded on the tape or a previously recorded scene will be erased (recorded over) regardless of whether the cassette holder came out or not. See page 21 for information about recording from the middle of a tape.

Image 10
Contents GR-DVX90 GR-DVX9 Dear Customer It is recommended that youEN3 Make sure you only use cassettes with the Mini DV markCU-V502E or AA-V51EA, AA-V51A CU-V502ED Remote Control Unit DC Cord RM-V716U Cleaning ClothDocking Station CamcorderAutomatic Demonstration Menu WheelLithium-ion is vulnerable in colder temperatures PowerCharging the Battery Pack About BatteriesTo Detach The Battery Pack Using the Battery PackUsing AC Power While sliding down BATT. RELEASE, detach itDioptre Adjustment Control Grip AdjustmentViewfinder Adjustment Tripod MountingSet the Operation Switch to and set the Power Date/Time SettingsBuilt-in Clock’s Rechargeable Lithium Battery Power Switch Power Lamp Lock Button Operation Menu WheelLoading/Unloading a Cassette OPEN/EJECT Switch Erase protection tab10 EN Cassette holder coverDisplay Recording Mode SettingEN11 Menu Screen Sub MenuLoading a MultiMediaCard 12 ENTo Unload a MultiMediaCard EN13 Picture Quality/Size Mode SettingApproximate Number of Storable Images Operation Switch Position Manual Operation ModePower Switch Position 14 ENEN15 Mode Dial PositionProgressive Mode FunctionPress START/STOP To Adjust The Brightness Of The Display16 EN To Stop RecordingSELF-RECORDING EN17Journalistic Shooting Self-Recording18 EN Snapshot Mode SelectionMotor Drive Mode Snapshot RecordingBasic Shooting Snapshot When unwanted still images are storedWhen you do not want to hear the shutter sound, set To Delete Unwanted Still ImagesZoom Slide the Power Zoom Lever towards T20 EN Zoom OutEN21 When a blank portion is recorded on a tapeProper recording Progressive Mode Recording To End Progressive Mode RecordingRegular shooting of moving images Description of Progressive Scan CCDEN23 Frame Scan a Scan BFocus Button Mode Dial toDual Shooting Fully-pressed PositionEN25 Feature Auto FocusFeature Manual Focus To obtain correct focusUsing Menus For Detailed Adjustment Menu Screen Explanations EN27After viewing demo, set to OFF Refer to Self-Timer  pgDemonstration will resume Automatic demonstration will not take placeEN29 Snapshot Flash If Auto Is SelectedEN31 Flash Brightness AdjustmentPower Switch Lock Button Operation Switch Menu Wheel DisplaySelf-Timer Rotate the Menu wheel to select , and press itSecond Recording Mode Dial to VideoEN33 Picture Wipe or Dissolve Selection Fade/Wipe EffectsFADE/WIPE Selection To Deactivate The Selected EffectFader And Wipe Menu EN35Menu Effect To Deactivate The Selected Mode Programme AE With Special EffectsDigital Sound Effects Sound Effect Mode SelectionTo cancel recording the sound effect midway EN37Exposure Control Iris LockEN39 White Balance AdjustmentManual White Balance Operation To Return To Automatic White BalancePower Zoom Lever VOL Menu Wheel Speaker Lock Button To Control The Speaker VolumeAvailable only with the remote control provided  pg Rewind ButtonEN41 Playback Sound 42 ENDisplay EN43 To cancel Blank Search midwayBlank Search Rotate the Menu wheel to select EXECUTE, then press itMail Clip Recording To cancel E-Mail Clip Recording44 EN To view video clips stored in a MultiMediaCardAuto Playback Normal PlaybackImages shot with the camcorder are automatically Index Screen If you press Index twice Index PlaybackEN47 If you press Index three timesTo Protect a File 48 ENProtecting Files To Remove ProtectionEN49 Power Switch Lock ButtonDeleting Files To Select a File by Browsing Files Stored in MemoryInitialising a MultiMediaCard Power Switch Menu Wheel Display50 EN You can initialise a MultiMediaCard anytimeTo Make The Print Frame Disappear Superimposing a Print FrameEN51 Press Print FramePrint Frame Deletion Set the Power Switch to52 EN Lock Button Delete Index Screen Deletion ConfirmationTo Delete ALL Print Frames 54 EN To Reset The SettingTo Print ALL Still Images ONE Print for Each EN55 To Reset The No. Of PrintsTo Print by Selecting Still Images and NO. of Prints 56 EN Docking Station AttachmentIf using a VCR . . . go to step If not . . . go to step EN5758 EN Connection To a Personal ComputerConnection To a Video Unit Equipped With a DV Connector EN59To use this camcorder as a player 60 ENDubbing To a VCR Engage the VCR’s AUX and Record-Pause modesEN61 To AUDIO, VIDEO* Video OUT connectorsDubbing From a VCR To use this camcorder as a recorderOptional 62 ENPlay Stop Core filter DV cable optional EN63To DV OUT 64 EN Indicator disappears when dubbing is completePower Switch Lock Button Snapshot Button Dubbing Images Stored In a MultiMediaCard To a TapeDubbing Images Recorded On a Tape To a MultiMediaCard Menu Wheel Power Switch Lock ButtonEN65 Tab Installing The Batteries66 EN Remote sensorEN67 Functions ButtonsFeature Playback Zoom Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback 68 ENEN69 Feature Playback Special EffectsEffect Select Menu VCR Recording deck 70 ENSET REMOTE/VCR Code You are now ready to try Random Assemble EditingMake Connections JVC VCR equipped with a remote pause connectorEN71 VCR other than aboveSelect Scenes 72 ENEditing Menu EN73 Automatic Editing to VCRDiagnosing VCR/CAMCORDER Timing 74 ENFor More Accurate Editing ProgrammeRecording deck Adjustment of VCR/CAMCORDER TimingEN75 Menu Dial DisplayAudio Dubbing Set 12BIT Mode to Sound 2 or MIX Menu Screen  pg76 EN To hear the dubbed sound during playbackAudio Dubbing Using Digital Sound Effects EN7778 EN Cleaning The CamcorderPush Here OPEN/EJECT Switch Hatch Lens blower After UseTroubleshooting Corrective ActionTroubleshooting 80 ENEN81 82 EN EN83  pg84 EN EN85 Auto Shut Off86 EN EN87 Appears while the tape is running 88 ENOrder of quality EN89 LCD Monitor/Viewfinder Indications During D.S.C. Playback Displays the sound modeLCD Monitor/Viewfinder Indications During Video Playback Displays the selected Digital Sound EffectEN91 Indications FunctionIndications While the Power Switch is set to92 EN DeletedPack, be sure to read the Terminals following cautions To prevent damage and prolong service lifeEN93 To avoid hazards94 EN About moisture condensation EN95To protect the unit, do not Serious malfunctioning96 EN EN97 Time Code  pg , 29, 41For Digital Video Camera 98 ENFor General For Digital Still CameraFor Connectors EN99EA/A/A-S/SH/ED