|
|
|
|
|
| EN |
| 41 | |
|
|
|
|
|
|
| |||
|
|
|
|
|
| ||||
|
|
|
|
|
|
| |||
|
| SYMPTOM |
|
| POSSIBLE CAUSE(S) |
| |||
| OTHER |
|
|
|
|
|
|
| |
| During recording, the indications do | ● Set “DISPLAY” to “FULL” in SYSTEM MENU (☞ pg. 24). | |||||||
| not appear. |
|
|
|
|
|
| ||
|
|
|
| ||||||
| The tape will not eject. | ● The battery pack is running low. | |||||||
|
|
|
| ● If the LCD monitor is not open over 60 degrees, the EJECT | |||||
|
|
|
| Switch does not function. | |||||
Some functions are not available. | ● The Power Switch is set to “ ”. |
●Certain combinations of modes or effects are not possible to use.
Vertical white lines appear when | ● This sometimes occurs when the contrast between the |
shooting a very bright object. | background and the object is great. It is not a defect of the |
| camcorder. |
|
|
Bright, | ● Sunlight is directly entering the lens. This is not a defect of |
the LCD monitor and the viewfinder. | the camcorder. |
|
|
The rear of the LCD monitor is hot. | ● The light used to illuminate the LCD monitor causes it to be |
| hot. Close the LCD monitor to turn it off or set the Power |
| Switch to “OFF”, and let the unit cool down. |
Colored bright spots appear all over the LCD monitor or the viewfinder.
●The LCD monitor and the viewfinder are made with high- precision technology. However, black spots or bright spots of light (red, green or blue) may appear constantly on the LCD monitor or in the viewfinder. These spots are not recorded on the tape. This is not due to any defect of the unit. (Effective dots: more than 99.99 %.)
The indicators and the picture color | ● This may occur when the surface or the edge of the LCD |
on the LCD monitor are not clear. | monitor is pressed. |
|
|
The LCD monitor, the viewfinder and | ● Wipe them gently with a soft cloth. Gently wipe in a |
the lens have become dirty | semicircular motion, as wiping strongly spreads the stain |
(ex. fingerprints). | and it won’t come out easily. |
|
|
An error number (i.e. E03) appears. | ● Turn the camcorder’s power off, then disconnect the power |
| source. After a few minutes, try turning the power on again. |
| If the error number still appears in the viewfinder, consult |
| your nearest JVC dealer. |
The image is out of focus.
●The diopter needs to be adjusted (☞ pg. 8).
●The scene being shot is adversely affecting the operation of Auto Focus (☞ pg. 28).
The picture is blurred in the Quick | ● This is normal while recording in the EP mode. Some noise |
Review or Retake mode. | may be present while recording in the SP mode (☞ pg. 12). |
|
|
The date and time displays | ● If you remove the power source from the camcorder while |
disappear. | the power is on, all settings and selections are erased. Make |
| sure to turn the camcorder’s power off before disconnecting |
| the power source. |
|
|
The wrong date and time are | ● If you have not performed Date/Time Setting (☞ pg. 9), the |
displayed/recorded. | date and time are not displayed/recorded correctly. Be sure |
| that Date/Time setting is carried out. |
|
|
Even though the lens cap is detached, | ● The “LENS CAP” warning indicator may blink when the |
the “LENS CAP” warning indicator | camcorder is used in dark areas, regardless of whether the |
(☞ pg. 47) blinks. | lens cap is attached or detached. |