JVC GR-SXM37 manual Getting Started, Refresh

Page 7

GETTING STARTED

Hook on

Push in

Power Switch

BATTERY RELEASE

Switch

Battery pack

To AC outlet To DC IN

connector

AC Adapter

Charging the Battery Pack

1)Hook the end of the battery pack to the

camcorder and push the battery in until it locks in place.

If the battery pack is attached wrongly, a malfunction may occur.

2)Set the Power Switch $ to “OFF” while pressing down the Lock Button #. Connect the AC Adapter to the DC IN connector !, then plug the AC Adapter to the AC Outlet.

3)The CHARGE lamp % blinks to indicate charging.

4)When the CHARGE lamp % stops blinking and turns off, charging is finished. Unplug the AC Adapter from the AC outlet. Disconnect the AC Adapter from the camcorder.

To Detach The Battery Pack…

slide BATTERY RELEASE 9 and pull out the battery pack.

Battery Pack

Charging time

BN-V10U

approx. 1 hr. 30 min.

 

 

BN-V12U (optional)

approx. 1 hr. 40 min.

 

 

BN-V20U (optional)

approx. 2 hrs. 40 min.

 

 

BN-V400U (optional)

approx. 5 hrs. 10 min.

 

 

Charging time is for a fully discharged battery pack.

Using the Battery Pack

Perform step 1) of “Charging the Battery Pack”.

Approximate recording time (unit: min.)

Battery Pack

Viewfinder on

LCD monitor on

 

 

 

BN-V10U

95

80

 

(50)

(45)

 

 

 

BN-V12U

100

85

(optional)

(55)

(50)

 

 

 

BN-V20U

160

140

(optional)

(85)

(80)

 

 

 

BN-V400U

380

330

(optional)

(210)

(195)

 

 

 

Using AC Power

Connect the AC Adapter to the camcorder ( step 2) of “Charging the Battery Pack”).

The provided AC Adapter features automatic voltage selection in the AC range from 110V to 240V.

ATTENTION:

Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can cause the camcorder to malfunction.

REFRESH:

Be sure to fully discharge a battery pack before recharging or storing it for a long period of time, otherwise the battery performance will be reduced.

1)Perform steps 1) through 3) of “Charging the Battery Pack”.

2)Press REFRESH " for over 4 seconds. The CHARGE lamp % blinks faster to indicate discharging.

3)When discharging is finished, charging automatically starts and the CHARGE lamp % blinks normally.

GETTING STARTED

7

Image 7
Contents Instructions ContentsOptional Accessories Provided AccessoriesProvided Accessories Safety Precautions Safety PrecautionsImportant Safety Instructions Safety Precautions# $ CONTROLS, Connectors and IndicatorsGetting Started LCD Monitor/Viewfinder Indications During Recording pg Getting Started Getting StartedRefresh Store Battery Date/Time SettingsGrip Adjustment Viewfinder AdjustmentPlayback RecordingRECORDING/PLAYBACK Basic Features Basic FeaturesConnections To a TV/VCR TBC Time Base CorrectorTape Dubbing Menu Settings Menu SettingsUsing The Cassette Adapter FADE/WIPE TOP MenuExposure 2000 1/2000 sec. High Speed ShutterSystem Menu Camera MenuDATE/TIME Disp Demo ModeOSD Output LCD BrightCounter Memory VCR MenuTroubleshooting TroubleshootingUsing Household AC Plug Adapter LCD Monitor To prevent damage to the LCD monitor, do NOT… To prolong service life…For Your Maintenance After Use Cleaning The CamcorderSpecifications Refresco Español AlimentaciónEspañol Alimentación AtenciónColocación/Extracción de un cassette Español Guia Para Operación RapidaEspañol Guia Para Operación Rapida Reproduccion DE Vídeo GrabaciónReproducción Para Grabación DE VídeoTerms