Erase protection switch*
Make sure the |
| |
window side is | Cassette holder | |
facing out. | ||
|
OPEN/EJECT
Switch
PUSH HERE
Cassette cover
*To Protect Valuable Recordings . . .
.... slide the erase protection switch on the back of the tape in the direction of “SAVE”. This prevents this tape from being recorded over. If you decide later that you do want to record on this tape, slide the switch back to “REC” before loading the tape.
EN11
Loading/Unloading A Cassette
The camcorder needs to be powered up to load or eject a cassette.
1 |
| OPEN CASSETTE COVER |
|
|
|
| ||||
|
|
|
| |||||||
| Slide OPEN/EJECT in the direction of the arrow then |
| ||||||||
STARTED | ||||||||||
|
| swing the cover open until it locks. The holder opens | ||||||||
|
|
| ||||||||
|
| automatically. |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
|
| •Do not touch internal components. |
|
|
|
| ||||
2 |
|
|
|
|
|
|
|
| GETTING | |
| INSERT/REMOVE TAPE |
|
|
| ||||||
|
|
|
|
| ||||||
| Insert or remove a tape and press “PUSH HERE” to |
| ||||||||
|
| close the cassette holder. |
|
|
|
| ||||
|
|
|
|
|
|
|
| |||
|
| •Once the cassette holder is closed, it recedes |
| |||||||
|
| automatically. Wait until it recedes completely |
| |||||||
|
| before closing the cassette cover. |
|
|
|
| ||||
|
| •When the battery’s charge is low, you may not be |
| |||||||
|
| able to close the cover. Do not apply force. Replace |
| |||||||
|
| the battery with a fully charged one before |
| |||||||
|
| continuing. |
|
|
|
|
|
| ||
3 |
|
|
|
|
|
|
|
| ||
| CLOSE CASSETTE COVER |
|
|
|
| |||||
|
|
|
|
|
|
|
|
| ||
Approximate recording time |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| |
Tape |
| Recording mode |
|
|
|
| ||||
|
|
|
|
|
|
| ||||
|
|
|
| SP |
| LP |
|
| ||
|
|
|
|
|
|
|
| |||
| 30 min. |
| 45 min. |
|
| |||||
|
|
|
|
|
|
|
| |||
| 60 min. |
| 90 min. |
|
| |||||
|
|
|
|
|
|
|
|
|
|
NOTES:
●It takes a few seconds for the cassette holder to open. Do not apply force.
●If you wait a few seconds and the cassette holder does not open, close the cassette cover and try again. If the cassette holder still does not open, turn the camcorder off then on again.
●If the tape does not load properly, open the cassette cover fully and remove the cassette. A few minutes later, insert it again.
●When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the cover.
●Closing the cassette cover before the cassette holder comes out may cause damage to the camcorder.
●Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder is closed with the camcorder switched off, however, it may not recede. It is recommended to turn the power on before loading or unloading.
●When resuming recording, once you open the cassette cover a blank portion will be recorded on the tape or a previously recorded scene will be erased (recorded over) regardless of whether the cassette holder came out or not. See page 21 for information about recording from the middle of a tape.