JVC 0303-MK-ID-SN No power is supplied, SET DATE/TIME! appears, Recording cannot be performed

Page 45

Before consulting your JVC dealer, please check the following to see it you can correct the problem yourself.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the beginning.

No power is supplied.

• The power is not connected properly.

¥Connect the AC Adapter securely ( pg. 7).

• The battery is dead.

¥Replace the dead battery with a fully charged one ( pg. 7, 8).

“SET DATE/TIME!” appears.

• The date/time is not set.

¥Set the date/time ( pg. 10).

•The built-in clock’s rechargeable lithium battery is discharged.

•The previously set date/time is erased.

¥Connect the camcorder to an AC outlet using the AC

Adapter for over 24 hours to charge the clock’s lithium battery ( pg. 49).

Recording cannot be performed.

—— For Tape Recording ——

•The tape’s erase protection tab is set to “SAVE”.

¥ Set the tape’s erase protection tab to “REC” ( pg. 9).

•The Power Switch @ is set to “ ” or “OFF”.

¥Set the Power Switch @ to “ ” or “ ” ( pg. 13).

• The VIDEO/MEMORY Switch t is set to “MEMORY”.

¥Set the VIDEO/MEMORY Switch t to “VIDEO”.

• “TAPE END” appears.

¥Replace with new cassette ( pg. 9).

• The cassette holder cover is open.

¥Close the cassette holder cover. —— For Memory Card Recording ——

• The VIDEO/MEMORY Switch t is set to “VIDEO”.

¥Set the VIDEO/MEMORY Switch t to “MEMORY”.

There is no picture.

•The camcorder is not getting power, or some other malfunction exists.

¥Turn the camcorder’s power off and on again ( pg. 13).

The focus does not adjust automatically.

• Focus is set to the Manual mode.

¥Set Focus to the Auto mode ( pg. 30).

•The recording was done in a dark place, or the contrast was low.

•The lens is dirty or covered with condensation.

¥ Clean the lens and check the focus again ( pg. 50).

The cassette will not load properly.

•The cassette is in the wrong position. ¥ Set it in the right position ( pg. 9).

•The battery’s charge is low.

¥Install a fully charged battery ( pg. 7, 8).

The memory card will not load properly.

•The memory card is in the wrong position. ¥ Set it in the right position ( pg. 11).

In the 5-Second mode, recording ends before

5 seconds have elapsed.

•The 5-Second mode is set to “Anim.” in the Menu Screen.

¥Select “5S” in the Menu Screen ( pg. 26).

Snapshot mode cannot be used.

• The Squeeze mode is selected.

¥Disengage the Squeeze mode ( pg. 33).

The colour of Snapshot looks strange.

•The light source or the subject does not include white. Or there are various different light sources behind the subject.

¥Find a white subject and compose your shot so that it also appears in the frame ( pg. 17, 29).

•The Sepia or Monotone mode is activated. ¥ Turn off Sepia and Monotone ( pg. 27).

The image taken using Snapshot is too dark.

•Shooting was performed under backlit conditions. ¥ Press the BACKLIGHT Button w ( pg. 30).

The image taken using Snapshot is too bright.

• The subject is too bright.

¥Set “PROGRAM AE” to “SPOTLIGHT” in the Menu Screen ( pg. 27).

Digital Zoom does not work.

• 10X*/16X** optical zoom is selected.

¥Set “ZOOM” to “40X” or “500X*/700X**” in the Menu Screen ( pg. 32).

•The VIDEO/MEMORY Switch t is set to “MEMORY”.

¥ Set the VIDEO/MEMORY Switch t to “VIDEO” ( pg. 13).

*GR-DX300 only.

**GR-DX95/DX75 only.

EN

TROUBLESHOOTING 45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents GR-DX300 GR-DX95 GR-DX75 Contents Safety Precautions Before recording an important scene Video/Editing Cable Remote Control Unit RM-V717U Tab AAA R03AC Adapter’s cord pg For attachmentRelease the stoppers on both ends of the Core Filter StopperSub Menu Charging the Battery Pack PowerUsing the Battery Pack Using AC PowerViewfinder Adjustment Grip AdjustmentLithium-ion is vulnerable in colder temperatures About BatteriesApproximate recording time Tape Recording mode Tripod MountingLoading/Unloading a Cassette Date/Time Settings Recording Mode SettingPress + or 5 to select Camera and press SELECT/SET To select the desired mode and press SELECT/SET Loading a Memory Card Picture Quality/Image Size SettingTo Unload a Memory Card Press + or 5 to select DSC and press SELECT/SETShooting while using the LCD monitor Open To Adjust The Brightness Of The DisplayShooting while using the viewfinder Pull out Basic RecordingPower-Linked Operation Operation ModeJournalistic Shooting Self-RecordingTime Code To Control The Speaker VolumeRecording from the Middle of a Tape Normal PlaybackBlank Search To cancel Blank Search midwayPress Blank Search r PressIf using a VCR . . . go to step If not . . . go to step ConnectionsTo TV or VCR To Delete Unwanted Still Images Basic Shooting SnapshotTo Remove The Shutter Sound To Protect Valuable Files available only for SD Memory CardSee ÒTo Adjust The Brightness Of The DisplayÓ on To Adjust The Brightness Of The DisplayApproximate Number of Storable Images GR-DX95/DX75Auto Playback Viewing File InformationIndex Playback Removing On-Screen DisplayAdvanced Features Protecting Files Deleting FilesTo Remove Protection To Make Thumbnail Images During Tape Recording Navigation FunctionTo ADD Thumbnail Images During Tape Playback To Delete Thumbnail ImagesMail Clip Recording To cancel E-Mail Clip RecordingTo Make Video Clips from REAL-TIME Camera Image To Make Video Clips from Recorded Video FootageTo Reset The Setting Setting Print Information Dpof SettingDubbing Still Images Recorded On a Tape To a Memory Card To Print ALL Still Images ONE Print for EachInitialising a Memory Card To Reset The No. Of PrintsMaking a New Folder Folder and File namesSnapshot Flash Flash Brightness AdjustmentPress + or 5 to select MANUAL, and press SELECT/SET If Auto Is SelectedSecond Recording GR-DX300 only To Take a Snapshot In The 5-Second Recording ModeInstead of pressing the Recording Start/Stop After approx secProgramme AE With Special Effects Night-ScopeFade/Wipe Effects Snapshot For Tape Recording Snapshot Mode SelectionAuto Focus Snapshot RecordingExposure Control Manual FocusPress + or 5 to select EXPOSURE, then press SELECT/SET To Return To Automatic Exposure ControlWhite Balance Adjustment Iris LockManual White Balance Operation Program AE WIPE/FADERExposure BalanceManual Camera Display SystemDSC For Playback MenuVideo Playback Sound Video DisplayDisplay DATE/TIME , Time CodeTo Use This Camcorder As a Player Dubbing To Or From a VCRTo Use This Camcorder As a Recorder DubbingTo DV Core filter DV cable optional To DV IN/OUT Slow-Motion Playback Using the Remote Control UnitPlayback Special Effects Playback ZoomAudio Dubbing Set 12bit Mode to Sound 2 or MIX Menu Screen  pgInsert Editing To hear the dubbed sound during playbackRandom Assemble Editing R.A.Edit SET REMOTE/VCR CodeMake Connections To Pause in j Select ScenesAutomatic Editing to VCR Adjustment of VCR/CAMCORDER TimingFor More Accurate Editing Diagnosing VCR/CAMCORDER TimingUsing DV cable Using USB cableUsing USB cable Connection To a Personal ComputerFocus does not adjust automatically No power is suppliedSnapshot mode cannot be used Image taken using Snapshot is too darkDuring R.A.Edit, the Dissolve function does Not work Black & White Fader does not workScene transition does not go as expected Image looks like the shutter speed is too slowAn error indication E03 or E04 appears An error indication E01, E02 or E06 appearsCharger indicator on the camcorder does Not light During recording, sound cannot be heardBattery Packs General Battery PrecautionsCassettes Memory CardsHow to handle a CD-ROM Built-in Clock’s Rechargeable Lithium BatteryLCD Monitor Main UnitCleaning The Camcorder For Your MaintenanceAfter Use About moisture condensationAC Adapter CamcorderFlash Remote Control Controls, Connectors And IndicatorsIndex Viewfinder SpeakerEdit Connector  pg @ Power SwitchDigital Video Input/Output Connector Blank Search Button  pg VIDEO/MEMORY SwitchDuring Memory Card Recording Only LCD Monitor/Viewfinder Indications1024 During Both Tape And Memory Card RecordingAppears when the Insert Editing w or Insert Appears when in the Squeeze, Cinema orOr Animation recording mode  pg Displays the sound mode for approx secondsHigh E01, E02 or E06 Unit in Safeguard Mode E03 or E04 Unit in Safeguard Mode EjectAppears if a file in another format is selected Terms SD Memory Card VIDEO/MEMORY Switch PositionUnload a Tape White BalanceAA/AG/AH/AS 0303-MK-ID-SN

0303-MK-ID-SN, ENLYT1127-001A specifications

The JVC ENLYT1127-001A,0303-MK-ID-SN is a state-of-the-art product designed for those who appreciate high-quality audio and functional versatility. This model stands out due to its exceptional sound performance, stylish design, and an array of features that cater to various user needs.

One of the main features of the ENLYT1127-001A is its advanced audio technology that delivers rich, clear sound across all frequency ranges. The device is engineered with high-fidelity components that minimize distortion, ensuring that users enjoy a pristine audio experience whether they're listening to music, watching movies, or gaming.

Additionally, the JVC ENLYT1127-001A incorporates innovative Bluetooth technology, allowing for seamless wireless connectivity with smartphones, tablets, and other devices. This wireless capability not only enhances convenience but also ensures that users can enjoy their audio content without the hassle of tangled wires.

The model also boasts a robust battery life, which is essential for users on the go. With quick charging capabilities, it provides extended usage time, making it an ideal choice for travel, outdoor adventures, or daily commutes. The ergonomic design of the device ensures comfort during extended use, making it suitable for long listening sessions.

In terms of compatibility, the JVC ENLYT1127-001A is designed to work with a variety of audio sources, from traditional music players to modern streaming services. This versatility means that users can enjoy their favorite media without limitations.

Another noteworthy characteristic is the sleek, modern aesthetic of the ENLYT1127-001A. Its design is not only functional, with intuitive controls that make operation straightforward, but also visually appealing, making it an attractive addition to any setup.

In summary, the JVC ENLYT1127-001A,0303-MK-ID-SN is a versatile and advanced audio solution that combines high-quality sound with modern features. Its impressive battery life, Bluetooth connectivity, and ergonomic design enhance the user experience, while its aesthetic appeal ensures it looks as good as it sounds. Whether you're a casual listener or a dedicated audiophile, this model promises to deliver an unparalleled audio experience that meets diverse needs.
Top Page Image Contents