Panasonic AJ-HDC27A Externally locking the time code, Example of connections for external lock

Page 57

Setting the time data

Externally locking the time code

1 Set the POWER switch to ON.

2 Set the TCG switch to F-RUN.

3 Set the DISPLAY switch to TC.

4 Supply the reference time code and reference video signal which are in a phase relationship that satisfies the time code standard to the TC IN connector and GENLOCK IN connector respectively.

3

2

1

Example of connections for external lock

The time code generator of the VTR unit can be locked to an external generator.

When locking to an external signal

The built-in time code generator is now locked to the reference time code.

About 10 seconds after locking, the external lock status will be retained even if the connection of the externally supplied reference time code is disconnected. However, the servo lock will be subject to disturbances if it is connected or disconnected during recording (REC).

<Note>

When the external lock operation is performed, the time code is instantly locked to the external time code, and the same value as the external code value appears on the counter display.

Do not set the unit to the recording mode during the few seconds it takes for the sync generator to stabilize.

User’s bit setting when the time code is externally locked

When the time code is externally locked, only the time data is locked to the time data of the external time code.

This means that the user’s bit can be set separately for each unit.

The user’s bit can also be locked to the user’s bit of the external time code. For details, consult your dealer.

To release the external lock

First stop supplying the external time code, and set the TCG switch to R-RUN.

When switching the power from the battery to an external power supply while the time code is externally locked

In order to ensure the continuity of the time code generator’s power, connect the external power supply to the DC IN connector, and then remove the battery pack. If the battery pack is removed first, no guarantees can be made for the continuity of the external locking of the time code.

Reference time code

TC IN

Reference video signal

GENLOCK IN

Gen-locking of the camera unit while the time code is externally locked

While the time code is externally locked, the camera unit is gen-locked by the reference video signal which is supplied to the GEN LOCK IN connector.

57

Image 57
Contents AJ- P FCC Note Indicates safety informationContents CAM Menus Setting menu screensFeatures Features of the camera unitIntroduction Remote control Piece filter disc sets available as standard accessoriesWide-ranging video gain selection Character display functionFeatures of the VTR unit FUJINON/CANON System ConfigurationSHAN-RC700 AJ-EC3Parts and their functions Power supply sectionCUE switch Audio in audio input selector switchAudio function section An audio component or microphones are connected hereAlarm warning alarm volume adjustment control DC OUT DC power output socketMonitor volume adjustment control = Monitor Select audio channel selector switchViewfinder section Synchro scan adjustment switches White BAL white balance memory selector switch$ Examples of filter selection Output output signal selector/AUTO Knee switch $ OUTPUT/AUTO Knee switch setting positionGain gain selector switch ECU Remote remote control connector 6- pin Shutter switchHD SDI OUT connector BNC SDI switchCharacter switch = VTR SAVE/STBY tape protection switchVTR Start button ? User 1 and User 2 buttons Mode Check button@ Eject button REW buttonLight switch Back tally switchBack tally lamp unit Display windowTime code related section Menu operation sectionDisplay switch Reset buttonTCG time code selector switch Hold buttonUsing the Anton/Bauer battery pack Power supplyPower output socket for lighting Lighting control switch Removal lever Battery packUsing the Panasonic AU-BP402 battery pack Using the Sony BP-90 battery pack Using the Sony NP-1 battery packUsing an AC power supply Using the Sony BP-L60/L90 lithium- ion batteryWhen the AJ-B75 AC adapter is used Pin noMount cap Attaching the lensMark Lens socketAdjusting the lens flange Adjustment methodApprox meters Gain L 0 dB Adjusting the white shadingShutter OFF Menu button JOG dial buttonCAM Main Menu White BAL switch Or B Auto W/B BAL switchStopper screw Attaching the viewfinderLever Viewfinder Adjusting the viewfinder positionAudio input preparation Locking screw Audio in switchesAJ-HVF27P Mic holderAttaching the AJ-MH700P mic holder optional accessory When attaching a microphone to the main unit for useScrews provided with mic holder Locking screwWhen connecting a microphone to the MIC in jack When connecting a microphone to the Audio in connectorAudio in connectors When connecting audio components When using a wireless microphoneMounting the unit on a tripod Tripod attachment Pan headTripod attachment Red lever Adjusting the shoulder pad position Attaching the shoulder strapBottom section Connecting the extension control unit Attaching the rain coverExample showing use of the Shan RC700 rain cover VTR Save VTR power-saving lamp Batt battery lampViewfinder lamp displays TALLY/REC recording lampSetting item Description of setting Setting the lamp displaysViewfinder screen status displays $ Display items and where they are displayedSafety zone markers Battery voltage display@ Master gain setting display Color temperature display PRE/A/BSelecting the display items On the VF Indicator screen of CAM MenuSelectable items Selecting the display itemsSetting change/adjustment result messages and display modes Display modes and setting change messagesMessage ScanSwitching the display mode Setting the camera IDSetting the marker displays Time code-related switch settings and display items Displays relating to errors and warningsScreen displays Displays relating to time codesAdjustments and setup using the setting menus Adjusting the date and timeAdjusting the white balance Adjusting the white balance and black balanceSet the switches as shown in the figure Output CAMMessage appearing upon completion of the adjustment Message appearing while the adjustment is in progressWhen the color temperature is lower than 2500 K When the color temperature is higher than 5600 KWhen there is no time to adjust the white balance When the white balance cannot automatically be adjustedMessages relating to white balance adjustment White balance memoriesExample of display When Filter INH is set to onAuto W/B switch Adjusting the black balanceSetting the shutter mode and speed Setting the electronic shutterShutter modes Available shutter modes and shutter speedsSetting the synchro scan mode Changing the shutter speed and mode selection rangeManual audio level adjustments Adjusting the audio levelLimiter Audio LevelSetting the user’s bit Setting the time data+ button ButtonTime code when the battery is replaced Setting the time codeUser’s bit setting when the time code is externally locked When locking to an external signalExternally locking the time code Example of connections for external lockUser data operation How to use the user dataSaving the user data Loading the user dataSetup card operations How to eject the setup cardHow to insert the setup card Error message Remedial action Formatting the setup cardConfig NG ErrorSaving the data settings on the card Give a title to the selected fileSelect the file No Write NG Format ErrorLoad the data of the selected file Loading the data saved on the cardRead NG No FileCassette tapes Ejecting the cassette when the battery has no chargeLoading a cassette tape Ejecting the cassette tapeRecording From providing the power supply to loading the cassetteTape function buttons ShootingScene-to-scene continuity During rec-pauseEnsuring scene-to-scene continuity at other times Rec review Lens RET button functionsColor playback Playback checking what has been recordedNews REC function Other VTR functionsRetake function Interval REC intermittent recording functionMenu operations When the power is switched on Status displayUser menu Engineer menuDisplaying menus Basic setting menu operationsUser menu Engineer menuOperations common to the user menu and engineer menu Displaying sub-menus and deciding on settingsExample Press the JOG Dial buttonSetting menu configuration SAT/PHASECAM Main Menu F16 ADJ Shutter White Preset Extender Filter Black STRSetting menu configuration PRO14 TRIM14 TRIM13 DIGITAL14 DIGITAL13 VTR Main MenuCAM Main Menu 1 screen Setting menu screens CAM MenuCAM Main Menu 2 screen CAM Main Menu 3 screenROP screen Setting menu screens CAM Main MenuMatrix screen ROP Remote Operation Panel is set on this screenColor Correction 1 screen Phase ENGColor Correction 2 screen SAT UserMID Setting screen LOW Setting screenLow level gain is set on this screen Middle level gain is set on this screenAdditional DTL 1 screen High Setting screenAdditional DTL2 screen High level gain is set on this screenSkin Tone DTL screen Knee settings of the camera are performed on this screenKNEE/LEVEL screen Skin tone detail of the camera is set on this screenCamera Setting screen Gamma settings of the camera are performed on this screenGamma screen VF Marker screen VF Display screenNormal ChangeCamera ID screen VF Indicator screenCamera ID is set on this screen IrisShutter Speed screen LED screenShutter speed is set on this screen Modes of the camera switches are set on this screen Camera SW Mode screenSuper Gain screen SmpteCAM Card READ/WRITE screen CAM Card R/W Select screenExample Lens adjustments are performed on this screen GENLOCK/IRIS screenLens ADJ screen CAM User Menu Select 1 screen CAM User Menu Select 1, 2 and 3 screensCAM User Menu Select 2 screen CAM User Menu Select 3 screenFlare screen Black Shading screenWhite Shading screen Colorimetry screenInitialize screen Diagnostic screenEvaluation screen Option screenOS/N measurement screen OResolution measurement screenOModulation measurement screen OSensitivity measurement screenVTR Main Menu screen Setting menu screens VTR MenuSetting menu screens VTR Main Menu Function screenVTR’s functions are set on this screen PRO14 BATTERY/TAPE screenTRIM14 TRIM13Battery Setting screen VTR VF Indicator screen MIC/AUDIO settings are performed on this screenMIC/AUDIO screen CH1/2 ChselCH3/4 MIXTC/UB screen Preset100 Regen101 TimeEXT VTR Initialize screen Time Date screenVTR User Menu Select screen VTR Card READ/WRITE screen103 104 LCD display 105Tally lamp What the warning Indicates106 Indicates VTR unit’s operationLamp flashes once a second Error codes Emergency eject107 Replacing the backup battery MaintenanceCondensation Head cleaning Cleaning inside the viewfinderPreparation for inspection Inspections prior to shootingInspecting the camera unit 109Inspecting the viewfinder Inspecting the aperture and zoom functions Inspecting the VTR unitTape travel inspection Manual audio level adjustment function inspection Automatic audio level adjustment function inspectionInspection using external microphones Earphone and speaker inspectionSpecifications VTR Video System Connector SectionVTR Audio System VTR Tape Transport SystemMaintenance products Relating to power supplyViewfinder Relating to external VTRsVQT9102-1 F1200W1021 @