Panasonic WV-CL920, WV-CL924 operating instructions VBS Gen-lock Mode Extvbs

Page 28

6.The VS gen-lock mode has a submenu for horizon- tal phase adjustments. When the cable length of the video output or the gen-lock input is changed, the horizontal phase must be re-adjusted.

7.The line-lock mode has a submenu for line-lock vertical phase adjustment. If the camera installation is relocated, check the vertical phase adjustment again since the AC line phase may be different.

6-1. VBS Gen-lock Mode (EXT(VBS))

 

** CAM SET UP **

** CAM SET UP **

CAMERA ID

OFF

CAMERA ID

OFF

ALC/ELC

ALC

ALC/ELC

 

ALC

SHUTTER

OFF

 

SHUTTER

 

OFF

 

 

AGC

 

ON (DNR-H)

AGC

 

ON (DNR-H)

SENS

UP

OFF

 

SENS UP

 

OFF

 

 

SYNC

 

INT

 

SYNC

 

EXT(VBS)

 

WHITE BAL

ATW1

WHITE BAL

ATW1

 

MOTION DET

OFF

 

MOTION DET

OFF

 

 

LENS

DRIVE

DC

 

LENS DRIVE

DC

 

 

END

SET UP ENABLE

END

SET UP ENABLE

1.Move the cursor to the SYNC parameter and select INT.

2.Connect the coaxial cable for the blackburst or composite color video signal to the gen-lock input connector.

3.Confirm that the INT parameter changed to EXT (VBS) on the menu.

Caution: The gen-lock input signal should meet the EIA RS-170A specifications and should not contain jitter, such as a VCR playback signal, as it could disturb synchronization.

4.After confirming that the cursor is on EXT (VBS),

press . The phase adjustment menu appears on the monitor.

** SYNC **

 

H PHASE

 

 

........I

 

 

-

+

SC COARSE

1(1--4)

 

SC FINE

....I....

 

-

+

RET END

5.Supply the video output signal of the camera to be adjusted and the reference gen-lock input signal to a dual-trace oscilloscope.

6.Set the oscilloscope to the horizontal rate and expand the horizontal sync portion on the oscillo- scope.

7.Move the cursor to H PHASE.

-29-

Image 28
Contents WV-CL924 Bol, within an equilateral triangle, is Contents Features PrefacePrecautions Clean the CCD faceplate with careDo not attempt to disassemble the camera Handle the camera with careMajor Operating Controls and Their Functions WV-CL924Auto Iris Lens Connector Flange-back Adjusting Ring FB0Gen-lock Termination Switch Hi-Z, G/L 75Ω 1Gen-lock Input Connector GEN-LOCK3Power Cord Socket 4AC/DC Compatible Input Terminal DC 12V IN/AC 24VWV-CL920 120 V AC 60Hz ConnectionsWV-CL924 12 V DC/24 V AC AC Power Supply Recommended wire gauge sizes for 24 V AC lineInstallation of Auto Iris Lens Connector Mounting the Lens Focus or FLANGE-BACK Adjustment Installation of Camera Mounting from the topSetup Camera Setup MenuATW1 ATW2 AWC Opening the Setup Menu Press and hold down for 2 seconds or moreSetup Operation All Reset OperationEditing the CAM SET UP Menu Important NoticeSetting Procedures Camera Identification Camera ID SettingTo edit the Camera ID To enter a blank space in the Camera IDTo erase all characters in the editing area Light Control Setting ALC/ELCTo determine the display position of the Camera ID ALC Mode with Preset on Back Light Compensation Back Light CompALC Mode with Preset OFF Blinking Shutter Speed Setting Shutter Gain Control Setting AGC ON/OFFElectronic Sensitivity Enhancement Sens UP Synchronization Setting Sync Important NoticesVBS Gen-lock Mode Extvbs Page VS Gen-lock Mode Extvs Line-lock Sync Mode LLPhase Coarse Auto-Tracing White Balance Mode ATW White Balance Setting White BALATW1 Auto Tracing White Balance Manual Fine Adjustment for AWC ATW Select AWC →Motion Detector Setting Motion DET Lens Drive Signal Selection Lens DriveSpecial Menu Special Burst BW To reset to the factory settings Prevention of Blooming and SmearSpecifications AGCPage Standard Accessories Optional Accessories Panasonic Canada Inc