Panasonic BM-ET500 operating instructions Precautions

Page 9

PRECAUTIONS

Refer all work related to the installation of this product to qualified service personnel or system installers.

Consult an expert on the load bearing capacity of the installation surface and structure. If the surface is not strong enough, the camera may fall down. Refer to the product specifications for weights.

Do not drop metallic parts through slots.

This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service.

Do not attempt to disassemble the appliance.

To prevent electric shock, do not remove screws or covers.

There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.

Handle the appliance with care.

Do not strike or shake, as this may damage the appli- ance.

Do not expose the appliance to water or moisture. Do not try to operate it in wet areas.

Take immediate action if the appliance gets wet. Turn the power off and refer servicing to qualified service personnel. Moisture can damage the appliance and also cause electric shocks.

Do not use strong or abrasive detergents when cleaning the appliance body.

Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.

Do not operate the appliance beyond its specified temperature, humidity, or power source ratings.

Use the appliance at temperatures between 0 °C and 40 °C {between 32 °F and 104 °F} and humidity between 30 % and 80 %. The input power source for this appliance is 32 V DC (when supplied from the con- trol unit) or 24 V DC (when supplied from an external power supply device).

This unit has no power switch.

Power is supplied from Control Unit BM-ED500 or from an external 24 V DC power supply device. Refer to the control unit's operating instructions for how to turn on/off the power.

When you use an external power supply device, do the following:

Turn on the external power supply device before turn- ing on Control Unit BM-ED500.

Turn off the external power supply device after turning off the control unit.

The third-party external power supply must be a UL Listed access control power limited device.

Consumable part

Contact your dealer for the front panel replacement, for example, when it is damaged or when you cannot rec- ognize or enroll yourself.

Part number of the front panel: 3CF001017AAA

Use of near-infrared ray

Near-infrared ray is used when iris data is enrolled or recognized by the unit. The near-infrared ray is compli- ant with the radiological safety standard of IEC60825-1.

Indication

Refer to the bottom of the unit as to the indications of equipment classification and power source, etc.

This product is not designed to prevent theft in advance. We shall not guarantee you for any trouble caused by using this unit.

If you are in a situation that iris recognition is impossible from the exterior, recognition or enrollment will be invalid.

Iris data is privacy. Take enough care not to leak the image data out of the administration PC. It is also recommended that you should get an agreement from a person to register his or her data.

We recommend that you note down your settings and save them. Power or battery failure may erase the setting.

Do the self-diagnostic test, when you open this unit door for maintenance, etc. The self-diagnostic test can be carried out by turning on a power supply. Read BM-ED500 Operating instructions for turning on a power supply.

9

Image 9
Contents Operating Instructions Lightning flash with arrowhead sym Important Safety Instructions Contents As a recognition camera for iris recognition PrefaceNumeric keys to enter the ID-and-password FeaturesAccess control system can be composed Automatic guidance and recognition by two camerasNotification about this Document TrademarksLimitation of Liability Document Convention Precautions Status Indicator Operation indicators LED indicatorUser guidance indicators Buzzer-level adjustment holeSide View Installations and ConnectionsWall InstallationCoaxial cable To Camera 1 3 of the control unit Dimensions of the Mounting Bracket Adjustments and Maintenance AdjustmentMaintenance Iris Recognition Recognition ProceduresWhen you have mistaken the entry of ID or password ID-and-password AuthorizationAdditional System Components Control Unit BM-ED500ES500E Problem Check item Remedy TroubleshootingPage Specifications GeneralInput/Output Standard Accessories Page Panasonic Digital Communications & Security Company