Axis Communications P1224-E user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 39

AXIS P1224–E Network Camera

System Options

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 32. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 43.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 10.

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The Axis product supports SD cards with the following file systems:

39

Image 39

Contents Axis P1224-E Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P1224-E Network Camera Table of ContentsShorten Sensor Unit Cable Hardware OverviewConnector Connectors and ButtonsNetwork Connector RJ12 ConnectorColor Indication LED IndicatorsSD Card Slot Control ButtonSet the Root Password Accessing the ProductAccess from a Browser Access from the InternetClick Use Https Set Power Line FrequencyLive View Controls on the Live ViewAMC Audio Controls Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerHow to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream Axis P1224-E Network Camera Basic Setup Setting Up the ProductImage VideoVideo Stream Pixel CounterCamera Settings Stream Profiles264 White Balance Exposure SettingsOverlay Image AppearancePrivacy Mask Overlay ImageGo to Video Overlay Image Axis P1224-E Network Camera Browser Viewer Description Live View ConfigDefault Viewer for Browsers Viewer SettingsGo to Setup Live View Config User Defined LinksOutput Buttons Go to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsAxis P1224-E Network Camera Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P1224-E Network Camera Events Recipient Use with action Setting Up an Action RuleRecipients Go to Events Action Rules and click AddGo to Events Recipients and click Add Setting Up an Email RecipientSchedules RecurrencesGo to Events Recurrences and click Add Go to Recordings List RecordingsRecording List Continuous RecordingIP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingAxis Video Hosting System Avhs Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Network Share Go to System Options Storage and click SD CardGo to System Options Storage Click Network Share Maintenance Ports & DevicesSupport Scripting AdvancedSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsUpgrading the Firmware TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserVideo Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalStorage disruption Storage and disk management problemsTechnical Specifications Installation aids General Casing Function/group SpecificationsInstallation Maintenance Built-inConnectors Function/group Specifications WarrantyFunction Pin Specifications Performance Considerations M3.2

Related manuals

Manual 104 pages 43.64 Kb