Axis Communications M3027PVE user manual Mount and Unmount SD Card, Format SD Card

Page 54

AXIS M3027–PVE Fixed Dome Network Camera

System Options

Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 10.

The following SD card file systems are supported:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — supported by most operating systems for personal computers.

The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card.

To avoid filling the card, it is recommended to remove recordings continuously. Under General Settings, select Remove recordings older than and select the number of days or weeks.

To stop writing to the card and protect recordings from being removed, select Lock under General Settings.

Mount and Unmount SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The SD card is automatically mounted when the card is inserted into the Axis product or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted.

To unmount the SD card:

1.Open the Axis product’s webpages and go to Setup > System Options > Storage.

2.Click SD Card.

3.Click Unmount.

4.The card can now be removed.

Format SD Card

NOTICE

Formatting the SD card will remove all data and recordings stored on the card.

Important

If autoformat is enabled, only use new or empty SD cards. Any data stored on the card will be lost when the card is inserted into the Axis product.

An SD card inserted into the product can be manually formatted to one of the supported file systems. To manually format the SD card, follow these steps:

1.Insert the SD card in the SD card slot.

2.Open the Axis product’s webpages and go to Setup > System Options > Storage.

3.Click SD Card.

4.Click Format and select the desired file system.

5.Click OK to start formatting the card.

54

Image 54

Contents Axis M3027-PVE Fixed Dome Network Camera Liability About this DocumentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis M3027-PVE Fixed Dome Network CameraPerformance Considerations Connectors and Buttons Network ConnectorHardware Overview SD Card Slot LED IndicatorsConnector Control ButtonAxis M3027-PVE Fixed Dome Network Camera Access the Product Access from a BrowserAccess from the Internet Camera Orientation Set the Root PasswordSet Power Line Frequency Click Use HttpsControls on the Live View Go to Setup EventsLive View Manual TriggerAxis Media Control viewer toolbar PTZ ControlsAxis M3027-PVE Fixed Dome Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream Axis M3027-PVE Fixed Dome Network Camera Set Up the Product Basic SetupPixel Counter VideoVideo Stream View modesOverview PanoramaDouble Panorama Quad View Image DirectionView areas Stream Profiles 264Image Appearance Camera SettingsExposure Settings White BalanceSet Shutter to View areasShutter & Gain Day/NightGo to Video Video Stream and select the Image tab OverlayOverlay Image Go to Video Overlay ImageUse Overlay Text in an Action Rule Go to Events Action RulesPrivacy Mask Viewer Settings Configure the Live ViewDefault Viewer for Browsers Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons Preset Positions PTZ Pan Tilt ZoomGuard Tour Controls AdvancedControl Queue Go to PTZ Guard Tour and click AddOperator Same as administrator but with lower priority Motion Detection DetectorsCamera Tampering Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAxis M3027-PVE Fixed Dome Network Camera Applications Install ApplicationGo to Setup Applications Application LicensesAxis M3027-PVE Fixed Dome Network Camera Convert Event Types to Action Rules Set Up Action RulesEvents Go to Events Action Rules and click AddTriggers Add Recipients ActionsRecipient Types Set Up Email Recipients Create SchedulesGo to Events Schedules and click Add Set Up Recurrences Go to Events Recurrences and click AddContinuous Recording RecordingsRecording List Go to Recordings ListClick Save to save and start the recording Languages Users System OptionsSecurity IP Address FilterIeee CertificatesGo to System Options Security Ieee Date & Time Basic TCP/IP SettingsGo to Setup System Options Security Certificates NetworkAssign IP Address Using ARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Video Hosting System AvhsLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 StorageUPnPTM BonjourMount and Unmount SD Card Format SD CardNetwork Share MaintenancePorts & Devices PortsSystem Overview SupportSupport Overview Logs & ReportsScripting Reset to Factory Default SettingsPlain Config File UploadEmergency Recovery Procedure TroubleshootingUpgrade the Firmware Check the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externallyVideo Camera Settings Problems with streaming H.264Video and image problems, general Key framesStorage and disk management problems Storage disruptionTechnical Specifications Power Function/group Specifications System ApplicationInstallation aids Data Streaming ConnectorsConnectors Performance Considerations M3.2