FEATURES
1.The following functions are built in.
(1)Auto Light Control (ALC)/Electronic Light Control (ELC)
(2)The
Dynamic range of 46 dB.
(3)Various External Sync Functions, including
(4)Auto/Manual White Balance Function
(5)Electronic Shutter Function
2.
3.Minimum illumination of 0.8 lx (0.08 footcandle) with F 1.4 lenses.
4.Minimum illumination of 0.4 lx (0.04 footcandle) with Panasonic aspherical high speed (F0.75) lenses.
5.480 lines of horizontal resolution
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
| q w e r |
| ||
|
|
|
| |
|
| !4 |
| |
|
| 120V | AC 60Hz | VIDEO OUT |
|
|
|
| |
Super Dynamic |
|
| ||
|
|
| ||
|
|
|
| |
| LOCK |
|
|
|
| t |
|
|
|
!1 | i |
| ||
|
|
| ||
|
| DC 12V | AC 24V |
|
| IN | INVIDEO OUT | ||
|
|
|
| |
|
| !5 | 1 |
|
| o | 2 |
| |
|
| |||
| y |
|
| |
|
| GND |
| |
u!0
!3
!2
!3
!2
Slide the panel to the left until it locks.
qAuto Iris Lens Connector
This connector is used to connect the auto iris lens with a
wFocus Fixing Screw
eFlange-back Adjusting Ring
This ring is used to adjust the back focal length or picture focus. Rotate this ring clock- wise for a
rLens (Option)
tCamera Mounting Screw Hole
This hole is used to mount the camera onto a mounting bracket.
CONNECTIONS
A. WV-CP460 (120 V AC 60 Hz)
1.Plug the AC power cord (supplied as standard accessory) into the AC Inlet Socket.
2.Connect the AC power cord to a 120V AC 60 Hz outlet.
Notes:
•Connect the power cord firmly.
•The power cord should be long enough for panning and tilting.
If the cable is too short, the power cord plug may be pulled off the camera when the camera pans or tilts.
B.WV-CP464 (12 V DC/24 V AC)
The
1.12 V DC Power Supply
Connect the power cord to the AC/DC compatible input terminal on the rear panel of the camera.
DC 12V | AC 24V |
|
| Resistance of copper wire [at 20°C (68°F)] | |||||||||
| IN |
|
| IN |
|
|
|
|
|
|
| ||
|
|
|
|
| 1 |
|
|
| Copper wire | #24 | #22 | #20 | #18 |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
| 2 |
|
|
| size (AWG) | (0.22mm2) | (0.33mm2) | (0.52mm2) | (0.83mm2) |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| Resistance | 0.078 | 0.050 | 0.030 | 0.018 | |
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| 12 V DC | Ω /m |
|
|
|
|
|
|
|
|
| GND |
| (10.8 V - 16 V) |
|
|
|
|
| |
|
|
|
|
|
| Resistance | 0.026 | 0.017 | 0.010 | 0.006 | |||
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| Ω /ft |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Calculation of maximum cable length between camera and power supply
10.8V DC ≤ VA - (R x 0.42 x L) ≤ 16 V DC
L : Cable length (m)
R : Resistance of copper wire (Ω /m)
VA : DC output voltage of power supply unit
L standard = | VA − | 12 |
| (m) |
|
|
| ||
|
| |||
| 0.42 x R | |||
L minimum = | VA − | 16 |
| (m) |
|
|
| ||
|
| |||
| 0.42 x R | |||
L maximum = | VA − | 10.5 |
| (m) |
|
|
| ||
|
|
| ||
0.42 x R