SETUP
1. CAMERA SETUP MENU
This camera utilizes a user setup menu that is displayed
• Opening the Setup Menu
Press and hold down 
for 2 seconds or more.
The CAM SET UP menu appears on the monitor as shown at right.
Check the current settings on the menu.
** CAM SET UP ** | Highlighted | |||
| ||||
CAMERA ID |
| OFF | ↵ |
|
ALC/ELC |
| ALC | ↵ |
|
SHUTTER |
| OFF |
|
|
AGC |
| ON |
|
|
SENS UP |
| OFF |
|
|
SYNC |
| INT |
|
|
WHITE BAL |
| ATW | ↵ |
|
MOTION DET | OFF |
|
| |
LENS DRIVE | DC |
|
| |
END | SET | UP DISABLE |
| |
Refer to the sections below for a detailed
description of menu items. If you decide not to make any changes after checking the cur-
rent settings, move the cursor to END at the start of the bottom line, and press | to close |
the CAM SET UP menu and return to normal camera picture mode. |
|
Note: If no button is pressed for 6 minutes while the CAM SET UP menu or any other menu is opened, the menu is automatically closed and the mode returns to the normal cam- era picture.
2. SETUP OPERATION
This camera utilizes a user setup menu (CAM SET UP) that is displayed on the monitor. To set items on the CAM SET UP menu, use the following buttons on the side panel.
Left Button 
Set Button
Up Button
Right Button
Down Button
Up Button ( | ): | Moves the cursor upwards. Use this button to select an item or adjust | |
|
| the parameters. |
|
Down Button ( | ): Moves the cursor downwards. Use this button to select an item or | ||
|
| adjust the parameters. | |
Right Button ( | ): | Moves the cursor to the right. Use this button to select or adjust the | |
|
| parameters of the selected item. The parameter changes each time | |
|
| this button is pressed. | |
Left Button ( | ): | Moves the cursor to the left. Use this button to select or adjust the | |
|
| parameters of the selected item. The parameter changes each time | |
|
| this button is pressed. | |
Set Button ( | ): | Executes selections and displays a submenu for an item with ↵ mark. | |
|
| END: Close Setup menu. | |
|
| RET: Return to the previous menu or page. | |
To return to the CAM SET UP menu |
| ||
Move the cursor to RET and press | . The CAM SET UP menu appears. | ||
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both 
and 
, press 
for a few seconds. The message ALL RESET momentarily appears on the monitor.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you can- not change the currently active settings. This is to prevent accidental changing of the settings.
To edit the CAM SET UP menu (change
settings), press 
and 
or 
and
to move the cursor to SET UP DIS- ABLE in the bottom line.
Press 
. SET UP DISABLE changes to SET UP ENABLE. Move the cursor to END, then to the item(s) you want to change.
| ** CAM SET UP ** | |||
CAMERA ID | OFF | ↵ | ||
ALC/ELC | ALC | ↵ | ||
SHUTTER | OFF |
| ||
AGC |
|
| ON |
|
SENS | UP | OFF |
| |
SYNC |
|
| INT |
|
WHITE BAL | ATW | ↵ | ||
MOTION DET | OFF |
| ||
LENS | DRIVE | DC |
| |
END |
|
|
| |
| SET | UP DISABLE | ||
| ** CAM SET UP ** | |||
CAMERA ID | OFF | ↵ | ||
ALC/ELC | ALC | ↵ | ||
SHUTTER | OFF |
| ||
AGC |
|
| ON |
|
SENS | UP | OFF |
| |
SYNC |
|
| INT |
|
WHITE BAL | ATW | ↵ | ||
MOTION DET | OFF |
| ||
LENS | DRIVE | DC |
| |
END |
|
|
| |
| SET | UP ENABLE | ||
Important Notice:
When the cursor is moved to END and the CAM SET UP menu closed after changing the parameters, the new values are saved in the EEPROM (Electric Erasable and Programmable Read Only Memory). These values remain valid until new values are saved, even if the power of the camera is off.
(To be continued reverse page)