Panasonic WV-CP464 Focus or FLANGE-BACK Adjustment, Installation of Camera, Mounting from the top

Page 4

Installation of Auto Iris Lens Connector

Install the lens connector (YFE4191J100) when using a video drive ALC lens.

The installation should be made by qualified service personnel or system installers.

(1)Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover as shown in the diagram below.

The pin assignment of the lens connector is as follows:

Pin 1: Power source; +9 V DC, 50 mA max.

 

 

 

 

Rib

 

Pin 3

Pin 2: Not used

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 3: Video signal; 1.3 V[p-p]/40 k

 

Pin 1

 

 

 

 

 

 

 

 

 

 

Pin 4: Shield, ground

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 4

 

 

 

 

 

 

 

(2) Solder the lens cable to the pins of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 2

supplied connector.

 

 

 

 

 

 

 

 

Mounting the Lens

Caution:

Before you mount the lens, loosen the screw on the side of the camera, and rotate this ring clockwise until it stops. If the ring is not at the end, the inner glass or CCD image sensor may be damaged.

1.Mount the lens by turning it clockwise on the lens mount of the camera.

2. Connect the lens cable to the auto iris lens connector on the side of the cam- era.

w

Flange-back

Adjusting Ring

Screw

q

Caution for Mounting the Lens

The lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter.

The protrusion at the rear of the lens should be as shown below:

C-mount: Less than 13 mm (1/2”)

CS-mount: Less than 8 mm (5/16”)

FOCUS OR FLANGE-BACK ADJUSTMENT

The following adjustment should be made by qualified service personnel or system installers.

1.Loosen the screw on the side of the camera.

2.Turn the flange-back adjusting ring to the desired position.

Caution: When the C-mount lens is mounted, do not rotate the ring counterclockwise by force after it stops. If the ring is rotated by force, the inner lens or CCD image sensor may be damaged.

3.Tighten the screw on the side of the camera.

Focusing of CS-mount lens

Screw

Focusing of

C-mount lens

Flange-back Adjusting Ring

Caution: Tightening the screw by force will cause damage to the screw or deviation of focus.

INSTALLATION OF CAMERA

Mounting from the top

Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket.

Make sure that the two original fixing screws are used when mounting the mount adapter as longer length screws may damage inner components.

Fixing Screws

Mount Adapter

Image 4
Contents Precautions PrefaceFeatures ConnectionsWV-CP460 120 V AC 60 Hz WV-CP464 12 V DC/24 V AC1Gen-lock Termination Switch Hi-Z, G/L 75 Ω 2Gen-lock Input Connector GEN-LOCK3Video Output Connector Video OUT AC Power SupplyInstallation of Camera Focus or FLANGE-BACK AdjustmentMounting from the top Opening the Setup Menu SetupEditing the CAM SET UP Menu Setting Procedures Camera Identification Camera ID SettingLight Control Setting ALC/ELC ALC Mode with SUPER-D2 onShutter Speed Setting Shutter Gain Control Setting AGC ON/OFFSynchronization Setting Sync ALC Mode with SUPER-D2 OFF and ELC ModeVBS Gen-lock Mode EXT VBS VS Gen-lock Mode EXT VSWhite Balance Setting White BAL Line-lock Sync Mode LLAuto-Tracing White Balance Mode ATW Fine Adjustment for AWC ATW ManuallyLens Drive Signal Selection Lens Drive Motion Detector Setting Motion DETSpecial Menu Specifications Standard AccessoriesOptional Accessories Panasonic Canada Inc