Kenwood TM-V708A instruction manual Preparation, Mobile Installation, Main Unit Installation

Page 8

PREPARATION

1MOBILE INSTALLATION

This transceiver allows you to install the front panel and main unit in separate locations. Select safe, convenient locations inside your vehicle that minimize danger to your passengers and yourself while the vehicle is in motion. Consider installing the units at appropriate positions so that knees or legs will not strike them during sudden braking of your vehicle. Try to pick well- ventilated locations that are shielded from direct sunlight.

Note: Unlike the previous KENWOOD mobile transceivers, this transceiver does not allow the front panel and main unit to be joined.

Main Unit Installation

1 Install the mounting bracket in the vehicle using the 4 supplied self-tapping screws and flat washers.

The bracket must be installed so that the 3 screw holes on the edge of each bracket side are facing the rear.

5 mm x 16 mm self-tapping screw

Flat washer

2Position the transceiver, then insert and tighten the 4 supplied hexagon SEMS screws and flat washers.

Double check that all hardware is tightened to prevent vehicle vibration from loosening the bracket or transceiver.

SEMS screw

Determine the desired angle of the main unit, using the 3 screw holes on the rear edge of each bracket side.

Position 1:

Position 2:

Position 3:

2

Image 8
Contents TM-V708A Features Thank YOUWhen condensation occurs inside the transceiver One or more of the following statements may be applicableContents Selecting the Number of Channels Using Visual Scan Setting Scan Limits Using Program ScanRecalling the Call Channel Reprogramming the Call Channel Locking Out a Memory ChannelPacket Operation Supplied Accessories Conventions Followed in this ManualPreparation Mobile InstallationMain Unit Installation Front Panel Installation Slide the front panel down until its locking tab clicksFixed Station Installation Modular Plug Cable ConnectionDC Power Cable Connection Mobile OperationFixed Station Operation Transceiver 15 a Supplied Accessory 20 a DC Power Cable Antenna ConnectionReplacing Fuses Fuse Location Fuse Current RatingMicrophone Accessory ConnectionsExternal Speakers Your First QSO Ewwew wGetting Acquainted Front Panel3SQL control Main Unit Front Microphone Indicators VFO mode Memory Recall modeProgrammable Memory PM mode Menu modeKEY Function Display Band a & B TX Band and Control BandTX Band Control BandMIC Keypad Direct Entry MC-58DM only Switching the Power ON/OFF Adjusting the VolumeOperating Basics Selecting a BandSelecting a Frequency Adjusting the SquelchPress VFO to select VFO mode Transmitting Selecting Output PowerWhen you finish speaking, release Mic PTT Menu Setup Menu AccessMenu Configuration Level Selections DefaultAuto PM Channel Store Channel DisplayMemory Channel Lockout Memory channel name See reference Number StoreAcknowledgement Automatic Power Off APORemote Control Operating Through Repeaters Offset Programming FlowProgramming Offset Selecting Offset DirectionSelecting Offset Frequency Press c / d to select Repeater Then press OKActivating Tone Function Selecting a Tone FrequencyPress Tone to activate the Tone function Press F, T.SELAutomatic Repeater Offset Transmitting a 1750 Hz Tone Press c/ d to select TX Hold 1-7-4, thenAutomatic Simplex Check ASC Press REV to switch the Reverse function on or OFFReverse Function Tone Frequency ID Press Scan to activate the Tone Frequency IDParameter Simplex Odd-split Memory ChannelsSimplex & Repeater or ODD-SPLIT Memory CHANNEL? Select your desired transmit frequency Press M.IN Storing ODD-SPLIT Repeater FrequenciesPress M.IN 1 s Select band a or B Press MR to enter Memory Recall mode Press MHz Tuning control+ Power onRecalling a Memory Channel Clearing a Memory ChannelTurn the Tuning control to select the first digit Naming a Memory ChannelPress a Repeat steps 5 and 6 to enter up to 8 digitsCall Channel Recalling the Call ChannelReprogramming the Call Channel Press VFOMEMORY-TO-VFO Transfer Channel DisplayPartial or Full RESET? Parameter Band a Band BProgrammable Memory PM Programmable InformationApplication Examples Situationit tiPress F, P.IN Storing in PM ChannelsRecalling a PM Channel Auto PM Channel Store PM Channel ResetPress PM+ Power on Scan Scan Type Scan RangeMode 1 31 ch Mode 2 61 chVisual Scan Selecting the Number of ChannelsTo exit Visual Scan, press ESC Using Visual ScanPress F, Visual to start Visual Scan Time-Operated mode Carrier-Operated modeSeek mode Selecting Scan Resume MethodVFO Scan Memory ScanPress VFO 1 s Select band a or BPress MHz Tuning control 1 s Group ScanLocking Out a Memory Channel To exit Group Scan, press MHz againSelect your desired frequency for the lower limit Press F Setting Scan LimitsProgram Scan Using Program Scan Select the appropriate bandTo exit Program Scan, press VFO again To exit MHz Scan, press MHz againCALL/VFO Scan CALL/MEMORY ScanTo exit Call/VFO Scan, press Call again To exit Call/Memory Scan, press Call againUsing Ctcss Continuous Tone Coded Squelch System CtcssPress the left or right Band SEL to select band a or B Press Tone to activate the Ctcss functionCtcss Frequency ID Press Scan to activate the Ctcss Frequency IDPress Tone to activate the DCS function Using DCSDigital Code Squelch DCS DCS Code ID Press Scan to activate the DCS Code IDFreq. Hz 1209 1336 1477 1633 Manual DialingDtmf Monitor Turn the Tuning control to select a character Automatic DialerStoring a Dtmf Number in Memory Repeat steps 4 and 5 to enter up to 8 digitsSelecting Pause Duration Transmitting a Stored Dtmf NumberSelecting TX Speed Programmable Function PF Keys PF PF1MR PF2 VFO PF3Press the numeric keys in sequence on the keypad Auxiliary FunctionsPress VFO Press Mic Enter Changing Frequency Step Size Programmable VFOPress VFO Press F, Step Press c/ d to select your desired step sizeDisplay Contrast Adjust Display DimmerAuto Dimmer Change POSITIVE/ Negative ReversalBlanking a Band Display Automatic Band Change ABCPWR switch MHz SQL controls VOL controls Press MNU to exit Menu modeTransceiver Lock ALL-CONTROL LockChanging Beep Volume Switching FM/AM ModeKEY Beep ON/ OFF Squelch Hang TimeTIME-OUT Timer TOT Automatic Power OFF APOIntermodulation and Sensitivity Adjustments Advanced Intercept Point AIPPOWER-ON Message Display Demonstration14 4 Press a Repeat steps 3 and 4 to enter up to 8 digitsSpeaker Mute Changing Speaker ConfigurationsConnection Mode Band a Band B Packet Operation Connecting with a TNC and Personal Computer FunctionSelecting a Data Transfer Rate Microphone Control with MC-58DM only KeyWireless Remote Control PreparationSelect the receive frequency on band B UHF Access Menu 1-A-3 Control and select onControl Operation Repeater Function VS-3 Voice Synthesizer Optional Band SELOptional Accessories PS-33 SP-50B VS-3PG-2N PG-3B PG-4X PG-5A MC-45Installing Options Installing the PG-4X Extension Cable KITRemove the 6 screws from the lower cover of the main unit Replace the lower cover 6 screwsConnections Using One PG-4X Kit Connections Using Two PG-4X KitsMaintenance ServiceService Note CleaningTroubleshooting Problem Probable Cause Corrective ActionSpecifications VHF Band UHF BandTransmitter Index

TM-V708A specifications

The Kenwood TM-V708A is a versatile and powerful dual-band transceiver that caters to amateur radio enthusiasts seeking advanced communication capabilities. Designed for operation in the 144 MHz and 440 MHz bands, this mobile radio provides exceptional performance in various modes, making it ideal for both casual users and serious operators alike.

One of the standout features of the TM-V708A is its ability to operate in both VHF and UHF frequencies simultaneous, enabling users to monitor multiple channels at once. With a powerful output of up to 50 watts on VHF and 35 watts on UHF, the TM-V708A ensures strong, clear signals that can reach distant stations. The user-friendly interface includes a large display that provides clear readings of the frequency and other operational parameters, enhancing the overall experience for operators.

The Kenwood TM-V708A is equipped with advanced digital signal processing (DSP) technology. This feature minimizes background noise, ensuring that voice communications remain crystal clear even in challenging conditions. The built-in CTCSS and DCS capabilities add further functionality, allowing for selective calling and improved privacy during conversations.

This transceiver comes with a wide range of operating modes. It supports FM, AM, and SSB, providing flexibility based on operator preference and environmental conditions. Furthermore, the inclusion of APRS (Automatic Packet Reporting System) capabilities allows for real-time tracking and position reporting, making it an excellent tool for emergencies and outdoor adventures.

Another notable characteristic is its built-in memory. The TM-V708A can store a substantial number of memory channels, allowing users to quickly access their preferred frequencies. Additionally, the dual-receive function permits the monitoring of two different frequencies simultaneously, providing seamless communication in dynamic environments.

For enhanced usability, the TM-V708A includes multiple connectivity options. It features a variety of ports for connecting external equipment, allowing operators to customize their setup according to their specific needs. The unit also balances robust performance with portability, making it suitable for both mobile and stationary use.

In summary, the Kenwood TM-V708A is a powerful and feature-rich transceiver that combines advanced technologies and user-friendly design. Its dual-band capabilities, robust power output, and extensive operational modes make it an invaluable tool for amateur radio operators seeking to enhance their communication experience. Whether for casual chatting or emergency response, the TM-V708A stands as a premier choice in the market.