Wi R I N G Th E Sy S T E M

CAUTION: Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system.

1.Configure the internal XCard crossovers prior to installation. Refer to the XCard Configurations on pages 14 & 15 for further information.

2.Plan the wire routing. Take care when running signal level RCA cables to keep them close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

3.Prepare the Power cable for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. The use of 4 gauge power cable can interfere with the installation of the end caps. Proper wire dress can prevent

this from occurring. To prevent the wire from fraying, strip the insulation at a 45° angle. Insert the bared wire into the B+ terminal with the long side of the insulation on the top. Bend the cable down at a 90° angle. Tighten

the set screw to secure the cable in place. We recommend using 4 gauge cables for power and for ground. This will give you the best performance possible.

STRIP WIRE

5/8"

AMP

INSULATION

4.Strip 3/8" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. Do not install the fuse at this time.

5.Prepare a length of cable to be used for the ground connection. Strip 5/8" of insulation from the end of the cable as described above and connect to the ground terminal of the amplifier. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the cable and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

6.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/4" of insulation from the wire end and crimping an insulated spade connector in place. Slide the connector over the REM terminal on the amplifier. Connect the other end of the REM wire to a switched 12 volt positive source. The switched signal is usually taken from the source unit's auto antenna or the accessory lead. If the source unit does not have these outputs available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

7.Securely mount the amplifier (with supplied screws) to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibrations or sudden vehicle stops.

8.Connect the source signal to the amplifier by plugging the RCA cables into the input jack(s) at the amplifier. If using Balanced Line Inputs, refer to pages 19 & 20.

9.Connect the speakers. Strip the speaker wires 5/8" and insert into the appropriate terminal on the amplifier. Insert the bared wire into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

10.Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems from road vibrations.

– 9 –

500.2 specifications

The Rockford Fosgate 500.2 is a powerful, high-performance amplifier that embodies the brand's signature commitment to quality and innovation in the world of car audio. Designed for audiophiles and casual listeners alike, this amplifier can dramatically enhance the sound experience in your vehicle, making it a popular choice for many car enthusiasts.

At the heart of the Rockford Fosgate 500.2 is its robust power output. The amplifier delivers a remarkable 250 watts per channel at 2 ohms, which ensures that even the most demanding speakers receive ample power. This efficiency allows users to enjoy loud and clear sound without distortion, even at higher volumes. The amplifier's dynamic power management ensures that the audio performance remains consistent across various listening scenarios.

One of the standout features of the 500.2 is its Smart Technology, which includes built-in thermal protection and short circuit protection. This design not only prolongs the life of the amplifier but also enhances performance by preventing overheating and damage during extended use. This is especially beneficial for users who love listening to music at high volume for prolonged periods.

The 500.2 also features a variable high-pass and low-pass crossover, allowing for precise sound tuning. Whether you are aiming for deep bass or crisp highs, the adjustable crossover settings enable users to customize their audio experience to their liking. With a frequency response range of 20 Hz to 20 kHz, this amplifier is versatile enough to handle a wide array of musical genres and audio formats.

Additionally, the amplifier's compact design allows for easy installation in various vehicle types without sacrificing valuable space. Its sleek and stylish chassis not only provides durability but also adds an aesthetic touch to your audio setup.

Lastly, the Rockford Fosgate 500.2 is built with quality materials that make it reliable and long-lasting. The unit's professional-grade construction ensures that it can withstand the rigors of daily use in a car environment. Overall, the Rockford Fosgate 500.2 is an excellent investment for anyone looking to upgrade their car audio system, offering powerful sound, innovative technology, and customization features that cater to both casual listeners and serious audiophiles.