Sharp Essential Operations and Features of the PN-E421 Flat Panel Television
Page 5

Basic Operation

 

1

2

3

 

 

4

5

6

 

7

8

 

1. INPUT (Input mode selection)

The menu is displayed. Press or to select the input mode, and press to enter.

*You can select the input terminal by pressing the input switch of the monitor.

Input mode

Video

Audio

PC D-SUB

PC D-sub input terminal

Audio input terminal

PC HDMI

PC/AV HDMI input terminal*1

*2

AV HDMI

PC/AV HDMI input terminal*1

 

When the PN-ZB01 (optional) is attached

Input mode

Video

Audio

PC DVI-D

PC/AV DVI-D input terminal*3

 

PC HDMI

PC/AV HDMI input terminal*1

 

PC D-SUB

PC D-sub input terminal

 

PC RGB

PC RGB input terminals*4

 

AV DVI-D

PC/AV DVI-D input terminal*3

*2

AV HDMI

PC/AV HDMI input terminal*1

 

AV COMPONENT

AV COMPONENT input terminals*4

 

AV S-VIDEO

AV S-video input terminal

 

AV VIDEO

AV video input terminal

 

*1 Select the terminal to be used in HDMI of INPUT SELECT. (See page 12.)

*2 Select the terminal for AUDIO SELECT which is used for audio input. (See page 12.)

*3 Select the terminal to be used in DVI of INPUT SELECT. (See page 12.)

*4 Select the terminal to be used in BNC of INPUT SELECT. (See page 12.)

2. DISPLAY

Displays monitor information. When you press this button again, the display disappears.

When the PN-ZB01 (optional) is attached, the display changes from INFORMATION1 → INFORMATION2 → clear display, and so on every time you press this button.

•The display disappears automatically after about 15 seconds.

•LAN is displayed during LAN communication.

•If LAN is displayed in red, there is a duplicate IP address.

3. MODE (Color mode selection)

Each time you press this button, the color mode changes in the following order:

STD (Standard) → VIVID → sRGB → STD...

•sRGB applies to PC input only.

sRGB is international standard of color representation specified by IEC (International Electrotechnical

Commission). Color conversion is made in taking account of liquid crystal’s characteristics and represents color tone close to its original image.

4.SIZE (Screen size selection) The menu is displayed.

Press or to select the screen size. (See page 6.)

5.MUTE

Turns off the volume temporarily.

Press the MUTE button again to turn the sound back to the previous level.

6. MENU

Displays and turns off the menu screen (see page 7).

7. VOL +/- (Volume adjustment)

Pressing or displays the VOLUME menu when the menu screen is not displayed.

V O L U M E

15

 

 

Press or to adjust the volume of the sound.

*If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears.

8. BRIGHT +/- (Backlight adjustment)

Pressing or displays the BRIGHT menu when the menu screen is not displayed.

B R I G H T

15

Press or to adjust the brightness.

*If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears.

5 E

Page 4 Page 6
Image 5
Page 4 Page 6
Contents PN-E471 PN-E421 Contents NRear view Part NamesNFront view Signal transmitter Power button Display button See Part Names NRemote control unitMode button See Size button See Menu button See Mute button SeeDisplay Basic OperationMute MenuWide Zoom Normal Basic Operation NSwitching the screen sizeDot by Dot Cut offDisplaying the menu screen Menu ItemsNExample of operation NMenu screen displayList of menu items Baud Rate LAN Setup Speaker Select Option DC OUT SettingMenu Items Menu PN-ZB01 optional Not attached AttachedLines Some items may not be displayed depending on the input modePIP/PbyP PbyP2 POSNPICTURE Menu item detailsNSCREEN NAUDIO NSETUP11 E NENLARGE PC input Menu Items NOPTIONMenu Items NDual screen display 13 ENPIP/PbyP Setting procedure NZOOM2 Special SettingMenu Items NEnlarge Enlarge menu, set Enlarge H/V and ENLARGE-POS H/V. See15 E PowerNSCHEDULE DAY of the WeekNScreen display for adjustment Adjustments for PC screen displayNAutomatic adjustment 17 E Controlling the Monitor with a PC RS-232C Communication procedurePC connection Communication conditionsNID numbers 19 ENCommunication interval VOLM0030 002VOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←21 E Setting of the Gamma user dataPower control/Input mode selection RS-232C command tableHow to read the command table Controlling the Monitor with a PC RS-232CAudio menu 23 EControlling the Monitor with a PC RS-232C Picture menu Controlling the Monitor with a PC RS-232C Setup menu Controlling the Monitor with a PC RS-232C Option menu 25 EImage Position Epos setting Controlling the Monitor with a PC RS-232C PIP/PbyP menu Initialization/Functional Restriction Setting Function menu27 E Controlling the Monitor with a PC RS-232C Others Commands for setting of the Gamma user dataControlling the Monitor with a PC LAN Settings to connect to a LAN29 E To set on the monitorControlling the Monitor with a PC LAN To set from a PC This monitor is factory preset as shown below IP AddressDefault Gateway 0.0 Controlling with a PC 31 EControlling the Monitor with a PC LAN Basic operationInformation about this monitor appears Setup SeeMonitor’s menu Screen See33 E User Name / PasswordDNS Server Accept IP AddressAuthentication Installation Information NAME/LOCATIONAccount Name / Password Monitor NameRecipient E-MAIL Addresses 35 ECondition ConfirmationTrap Setting Snmp SettingTrap When Authentication Fails Version37 E TroubleshootingNProduct Specifications SpecificationsVesa DDC2B Vesa DPMS, DVI Dmpm39 E NDimensional DrawingsSpecifications NDDC plug and play Specifications NPower managementDmpm Digital Monitor Power Management 41 E Specifications NCompatible signal timing PCNCompatible signal timing AV NPC D-sub input terminal pins Specifications NPC/AV DVI-D input terminal pinsNPC/AV DVI-D output terminal pins NPC/AV Hdmi input terminal pinsPN-E471E421 G EN10B2
Related manuals
Manual 43 pages 47.52 Kb Manual 16 pages 12.04 Kb
Top Page Image Contents