Sharp PN-E421, PN-E471 manual 11 E, Naudio, Nsetup

Page 11

nAUDIO

TREBLE

Adjusts the volume of treble-level sound.

BASS

Adjusts the volume of bass-level sound.

BALANCE

Adjusts the balance of the audio sound between right and left.

RESET

Resets the values of the AUDIO menu items to the factory preset values.

Select “ON” and then press .

nSETUP

OSD H-POSITION

Adjusts the horizontal display position of menu screen.

OSD V-POSITION

Adjusts the vertical display position of menu screen.

MONITOR (for PN-E421 only)

Select the installation direction of the monitor.

LANDSCAPE

Horizontal orientation

PORTRAIT

Vertical orientation

MONAURAL AUDIO

Outputs audio signals as monaural.

LANGUAGE

Sets the display language for the menu screen.

POWER ON DELAY

You can delay the screen display after the monitor is turned on. The period can be set up to 60 seconds in units of one second. When this function is activated, the power LED flashes (at approx. 1 second interval) in orange. This function is disabled when 0 is specified.

STANDBY MODE

When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in standby mode.

When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer. Also, certain RS-232C commands cannot be used in standby mode, and control via LAN will be disabled. (See pages 22 and 29.)

HDMI SETTING

HDMI AUTO VIEW

..........................When ON is selected, the screen size is

adjusted automatically according to the screen size control signal included in the video signal input from the AV HDMI input terminal.

HDMI RGB INPUT RANGE

..........................Sets the type of HDMI signals when using

the AV HDMI input mode.

When AUTO is selected, the type is set automatically.

HOT PLUG CONTROL

Sets whether to use hot plug control for the PC/AV HDMI and PC/AV DVI-D input terminals.

Menu Items

RS-232C/LAN SELECT

Selects the method with which to control the monitor from the computer.

ID No. SET

Assigns ID numbers to monitors connected in a daisy chain (see page 19), using RS-232 cables.

The numbers 1 to 255 are available for ID numbers.

If “0” is set, the system regards this as the state where no ID number is set.

BAUD RATE

Selects the communication speed used for RS-232C communication.

LAN SETUP

Configures the settings to control the monitor from the computer via LAN. (See page 29.)

SPEAKER SELECT

Selects the speaker to be used.

OPTION DC OUT SETTING

Normally, leave this setting as OFF.

When using an optional part, if instruction appears, change the setting accordingly.

11 E

Image 11
Contents PN-E471 PN-E421 Contents NRear view Part NamesNFront view Mute button See Part Names NRemote control unitSignal transmitter Power button Display button See Mode button See Size button See Menu button SeeMenu Basic OperationDisplay MuteCut off Basic Operation NSwitching the screen sizeWide Zoom Normal Dot by DotNMenu screen display Menu ItemsDisplaying the menu screen NExample of operationMenu PN-ZB01 optional Not attached Attached Baud Rate LAN Setup Speaker Select Option DC OUT SettingList of menu items Menu ItemsPbyP2 POS Some items may not be displayed depending on the input modeLines PIP/PbyPNPICTURE Menu item detailsNSCREEN NAUDIO NSETUP11 E NENLARGE PC input Menu Items NOPTIONMenu Items NDual screen display 13 ENPIP/PbyP Enlarge menu, set Enlarge H/V and ENLARGE-POS H/V. See NZOOM2 Special SettingSetting procedure Menu Items NEnlargeDAY of the Week Power15 E NSCHEDULENScreen display for adjustment Adjustments for PC screen displayNAutomatic adjustment 17 E Communication conditions Communication procedureControlling the Monitor with a PC RS-232C PC connectionNID numbers 19 ENCommunication interval OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ← 002VOLM0030 VOLM0020 ←21 E Setting of the Gamma user dataControlling the Monitor with a PC RS-232C RS-232C command tablePower control/Input mode selection How to read the command tableAudio menu 23 EControlling the Monitor with a PC RS-232C Picture menu Controlling the Monitor with a PC RS-232C Setup menu Controlling the Monitor with a PC RS-232C Option menu 25 EImage Position Epos setting Controlling the Monitor with a PC RS-232C PIP/PbyP menu Initialization/Functional Restriction Setting Function menu27 E Controlling the Monitor with a PC RS-232C Others Commands for setting of the Gamma user dataTo set on the monitor Settings to connect to a LANControlling the Monitor with a PC LAN 29 EControlling the Monitor with a PC LAN To set from a PC This monitor is factory preset as shown below IP AddressDefault Gateway 0.0 Basic operation 31 EControlling with a PC Controlling the Monitor with a PC LANScreen See Setup SeeInformation about this monitor appears Monitor’s menuAccept IP Address User Name / Password33 E DNS ServerMonitor Name Installation Information NAME/LOCATIONAuthentication Account Name / PasswordConfirmation 35 ERecipient E-MAIL Addresses ConditionVersion Snmp SettingTrap Setting Trap When Authentication Fails37 E TroubleshootingVesa DPMS, DVI Dmpm SpecificationsNProduct Specifications Vesa DDC2B39 E NDimensional DrawingsSpecifications NDDC plug and play Specifications NPower managementDmpm Digital Monitor Power Management 41 E Specifications NCompatible signal timing PCNCompatible signal timing AV NPC/AV Hdmi input terminal pins Specifications NPC/AV DVI-D input terminal pinsNPC D-sub input terminal pins NPC/AV DVI-D output terminal pinsPN-E471E421 G EN10B2
Related manuals
Manual 43 pages 47.52 Kb Manual 16 pages 12.04 Kb