Sharp LC-60LE360X Using a PC, PC compatibility chart, RS-232C commands list, PC Control of the TV

Using a PC

PC compatibility chart

	Resolution		Horizontal	Vertical	VESA	Analogue	Digital (HDMI)
			Frequency	Frequency	Standard	(D-Sub)
VGA		640 g 480	31.5 kHz	60 Hz			
SVGA		800 g 600	37.9 kHz	60 Hz			
XGA		1024 g 768	48.4 kHz	60 Hz			
WXGA		1360 g 768	47.7 kHz	60 Hz			
1080P		1920 g 1080	67.5 kHz	60 Hz			

DDC is a registered trademark of Video Electronics Standards Association. Power Management is a registered trademark of Sun Microsystems, Inc.

VGA, SVGA, XGA and WXGA are registered trademarks of International Business Machines Corporation.

RS-232C commands list

Commands

• Commands not indicated here are not guaranteed to operate.

CONTROL ITEM	COMMAND				PARAMETER				CONTROL CONTENTS
POWER SETTING	P	O	W	R	0	_	_	_	POWER OFF (STANDBY)
	I	T	G	D	_	_	_	_	INPUT SWITCHING (TOGGLE)
INPUT SELECTION	I	T	V	D	_	_	_	_	ATV (CHANNEL FIXED)
	I	D	T	V	_	_	_	_	DTV (CHANNEL FIXED)
	I	A	V	D	*	_	_	_	INPUT 1 – 9 (1 – 9)
	D	C	C	H	*	*	_	_	ATV DIRECT CHANNEL (1 – 99)
	C	H	U	P	_	_	_	_	ATV CHANNEL UP
CHANNEL	C	H	D	W	_	_	_	_	ATV CHANNEL DOWN
	D	T	V	D	*	*	*	_	DTV DIRECT CHANNEL (1 – 999)
	D	T	U	P	_	_	_	_	DTV CHANNEL UP
	D	T	D	W	_	_	_	_	DTV CHANNEL DOWN
	A	V	M	D	0	_	_	_	TOGGLE
	A	V	M	D	1	_	_	_	STANDARD
AV MODE SELECTION	A	V	M	D	2	_	_	_	MOVIE
	A	V	M	D	5	_	_	_	DYNAMIC

PC Control of the TV

•When a programme is set, the TV can be controlled from the PC using the RS-232C terminal.

The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and settings can be made, enabling automatic programmed playing.

•Attach an RS-232C cable cross-type (commercially available) to the Din/D-sub RS-232C for the connections.

NOTE

•This operation system should be used by a person who is accustomed to using PCs.

Command format

Eight ASCII codes e CR

C1 C2 C3 C4 P1 P2 P3 P4

Command 4-digits Parameter 4-digits Return code

Command 4-digits: Command. The text of four characters.

Parameter 4-digits: Parameter 0 – 9, space, ?

	A	V	M	D	6	_	_	_	DYNAMIC (FIXED)
	A V M D 7					_	_	_	PC
VOLUME	V	O	L	M	*	*	*	_	VOLUME (0 – 100)
	H	P	O	S	*	*	*	_	H-POSITION (PC) (000 – 180)
POSITION	V	P	O	S	*	*	*	_	V-POSITION (PC) (000 – 120)
	C	L	C	K	*	*	*	_	CLOCK (000 – 180)
	P	H	S	E	*	*	*	_	PHASE (000 – 015)
	W	I	D	E	0	_	_	_	TOGGLE (AV)
	W	I	D	E	1	_	_	_	NORMAL (AV)/4:3 (USB – MOVIE)
	W	I	D	E	2	_	_	_	ZOOM 14:9 (AV)
	W	I	D	E	3	_	_	_	PANORAMA (AV)
	W	I	D	E	4	_	_	_	FULL (AV)/16:9 (USB – MOVIE)
	W	I	D	E	5	_	_	_	CINEMA 16:9 (AV)
						_	_	_

Communication conditions

Set the RS-232C communications settings on the PC to match the communications conditions of the TV. The communications settings of the TV are as follows:

Baud rate:	9,600 bps
Data length:	8 bits
Parity bit:	None
Stop bit:	1 bit
Flow control:	None

Communication procedure

Send the control commands from the PC via the RS-232C connector.

The TV operates according to the received command and sends a response message to the PC.

Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command.

Parameter

Input the parameter values, aligning left, and fi ll with space(s) for the remainder. (Be sure that four values are input for the parameter.)

When the input parameter is not correct, “ERR” returns. (Refer to “Response code format”.)

0 0 0 0 9 a 3 0

Response code format

Normal response

OK

Return code (0DH)

Problem response (communication error or incorrect command)

E R R

Return code (0DH)

WIDE MODE	W	I	D	E	6				CINEMA 14:9 (AV)
	W	I	D	E	7	_	_	_	NORMAL (PC)
	W	I	D	E	9	_	_	_	FULL (PC)
	W	I	D	E	1	0	_	_	DOT BY DOT (PC)
	W	I	D	E	1	1	_	_	UNDERSCAN
	W	I	D	E	1	2	_	_	AUTO (USB – MOVIE)
	W	I	D	E	1	3	_	_	JUST SCAN (USB – MOVIE)
	M	U	T	E	0	_	_	_	TOGGLE
MUTE	M	U	T	E	1	_	_	_	MUTE ON
	M	U	T	E	2	_	_	_	MUTE OFF
	A	C	S	U	0	_	_	_	SRS TS HD TOGGLE
SRS TS HD	A	C	S	U	1	_	_	_	SRS TS HD ON
	A	C	S	U	2	_	_	_	SRS TS HD OFF
AUDIO CHANGE	A	C	H	A	_	_	_	_	TOGGLE
	O	F	T	M	0	_	_	_	OFF
	O	F	T	M	1	_	_	_	SLEEP TIMER 30 MIN
SLEEP TIMER	O	F	T	M	2	_	_	_	SLEEP TIMER 1 HOUR
	O	F	T	M	3	_	_	_	SLEEP TIMER 1 HOUR 30 MIN
	O	F	T	M	4	_	_	_	SLEEP TIMER 2 HOUR
	O	F	T	M	5	_	_	_	SLEEP TIMER 2 HOUR 30 MIN
TEXT	T	E	X	T	0	_	_	_	TEXT OFF
	T	E	X	T	1	_	_	_	TEXT CHANGE TOGGLE

NOTE

•If an underbar (_) appears in the parameter column, enter a space.

•If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.

- 13