Part names and functions
Watching TV
TV (Rear)
Turning the TV on/off |
| Checking Signal information |
|
|
|
15 | DIGITAL |
|
| |
AUDIO |
|
| ||
| OUTPUT |
|
| |
16 |
| HDMI 1 | 1 | |
|
| |||
|
|
| ARC | |
|
|
|
| |
| PC |
| ||
| ANALOGUE |
|
| |
17 | RGB (PC) |
|
| |
INPUT 6 | 6 |
| ||
|
| |||
| COMPONENT/AV INPUT | |||
| R - AUDIO - L | VIDEO/Y PB(CB) | PR(CR) | |
| R - AUDIO - L | R - AUDIO - L | VIDEO | |
| AUDIO OUT | INPUT 7 | 7 | |
18 19
AUDIO IN
23
USB 2
DC5V 0.5A
HDMI 5
5
HDMI 4
4
OUTPUT DC5V 1.5A
1
2
3
4
5
| C.I. |
| USB 1 |
DC5V 1.5A | |
MHL | HDMI 2 |
2 | |
(DC5V 900mA) | |
| OUTPUT |
AUDIO(L/R) | |
| HDMI 3 |
| 3 |
CAUTION
Use a Product with the following thickness for optimal connection to HDMI cable/ UBS device.
6
7
8
9
10
Turning on/off the power
•To turn on the power
Press POWER on the TV. (After a few seconds, an image appears with sound.)
•To turn off the power
Switch it off by pressing POWER on the TV.
Standby mode
•To standby mode
If the TV is switched on, you can switch it to standby by pressing POWER on the remote control.
•Switching on from standby
From standby, press POWER on the remote control.
NOTE
•If you are not going to use this TV for a long period of time, be sure to remove the AC cord from the AC outlet.
•Minor power is consumed when the unit is in standby mode.
If you install a
ATV/DTV
1 Press MENU and the MENU screen displays.
2 Press c/d to select “
” (Programme setup).
3 Press a/b to select “Digital setting”, and then press ENTER.
4 Press a/b to select “Signal information”, and then press ENTER.
20 | 21 | 22 | 14 | 13 | 12 | 11 |
Initial auto installation
• The “Signal information” screen will appear.
Auto installation
1POWER (On/Off) button
2 MENU button
3 INPUT button
4 Channel up (r)/ down (s) buttons 5 Volume up (+) /down
6 C.I. (COMMON INTERFACE) slot*1
7 USB 1 terminal
8 INPUT 2 (HDMI/MHL) terminal
9Headphone jack ( 
3.5 mm)
•The speakers do not output volume when headphones are plugged in.
10INPUT 3 (HDMI) terminal
11OUTPUT terminal (For power output only)*2
12INPUT 4 (HDMI) terminal
13INPUT 5 (HDMI) terminal*3
14USB 2 terminal
15DIGITAL AUDIO OUTPUT terminal
16INPUT 1 (HDMI/ARC) terminal
17INPUT 8 terminal*3
18AUDIO IN terminal
19Antenna input terminal
20AUDIO OUT terminals
21INPUT 7 terminals
22INPUT 6 terminals
23
When the TV powers on for the first time after purchase, the initial auto installation wizard appears. Follow the menu and make the necessary settings one after another.
1 Press POWER on the TV.
• The initial auto installation wizard appears.
2 Press a/b to select your country channels listed on the screen, and then press ENTER.
Press a/b to select the desired language, and then press ENTER.
Press a/b to select “HOME” or “STORE”, and then press ENTER.
HOME:
•“STANDARD” will be the default value for the “AV mode” setting.
STORE:
• “DYNAMIC (FIXED)” will be the default value for the |
“AV mode” setting. If the “AV mode” is changed, the TV |
You can run auto installation again, even after setting up the preset channels.
1 Press MENU and the MENU screen displays.
2 Press c/d to select “
” (Programme setup).
3 Press a/b to select “Auto installation”, and then press ENTER.
If you have already set the password, enter it here.
• See page 7 for setting a password.
4 Press a/b to select your country channels listed on the screen, and then press ENTER.
Press a/b to select the desired language, and then press ENTER.
*Press a/b to select “DTV”, “ATV” or
“DTV + ATV”, and then press ENTER.
*1 | This function applicable for certain countries only. |
*2 | This terminal can supply power for dongles. (Availability is depend on the specifi cation of dongle). |
*3 | The INPUT 5 and INPUT 8 terminals can both use the same analogue audio input terminal. However, the proper item must |
| be selected in the “Audio select” menu. (See page 9.) |
•The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
•The illustrations used throughout this manual are based on
will automatically switch back to “DYNAMIC (FIXED)” |
when there is no further change to TV setting for 30 |
minutes. |
• The confi rmation screen appears only when selecting |
“STORE”. Press a/b to select “Yes” or “No”. |
• To change the STORE mode to HOME mode, please |
refer to page 9 to reset the unit. |
* Press a/b to select “DTV”, “ATV” or “DTV + ATV”, and then press ENTER.
•Auto installation will be executed.
•You do not need to do anything during the auto search.
•If you select “Others” country, some of DTV channel may not tune properly.
You do not need to do anything during the auto search. Press MENU to exit.
*
NOTE
•In the setting of some country, selecting of “DTV”, “ATV” or “DTV + ATV” may not be shown.
•A region or service selection screen may display depending on the country settings or cable providers selections. Follow the screen prompts to make the selections.
- 5