Crossover Network Installation

GETTING STARTED

•Turn off the audio system. It is also advisable to disconnect the negative (–) terminal of your vehicle’s battery whenever performing installation work.

•Before cutting, drilling or inserting any screw, check clearances on both sides of the planned mounting surface. Also check for any potential obstacles, such as window tracks and motors, wiring harnesses, etc. Check both sides of the

vehicle, many vehicles are not symmetrical!

•Always wear protective eyewear.

The crossover networks supplied with your C2 System should be installed in a dry location inside your vehicle. DO NOT INSTALL THEM INSIDE OF A DOOR! Doors often get wet on the inside, which can damage your crossover networks and could potentially damage your entire sound system. The crossovers can be screwed into a solid surface via two holes located under the protective cover of the case. To access these holes, simply squeeze the sides of the cover while gently pulling the cover away from the base. Make sure that your mounting location will not cause damage to wiring, fuel lines, brake lines or any other vital component of your vehicle. Once you have screwed the case in and made your connections, snap the protective cover back into place.

!! WARNING

It is absolutely vital that your component system is connected as shown in this manual. Failure to connect the system as shown may result in damage to your speakers which is NOT covered under warranty.

Do not substitute different crossover networks into your C2 System. Do not use crossover networks intended for different C2 models.

Ampliﬁer

Output

TWEETER PROTECTION

The C2 crossover networks are equipped with an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. This electronic device monitors current going to the tweeter and will disconnect the tweeter from the signal when it senses overload. Should this occur while listening to the audio system, simply reduce the volume for a few seconds and the protection circuit will reset itself automatically.

CROSSOVER NETWORK ADJUSTMENT

The crossover networks have been designed to allow tonal adjustments to the tweeter level. These adjustments make it possible to fine-tune your system to suit your listening preferences and to compensate for various speaker mounting applications.

4 JL Audio - C2-600 Owner’s Manual

C2-600, C2-600-02102009, C2-600cw, C2-600-XO specifications

JL Audio is renowned for their high-performance audio equipment, and the C2 series of speakers is a testament to their commitment to quality sound. The C2-600cw, C2-600-XO, and C2-600-02102009 models are particularly noteworthy, showcasing a combination of advanced technologies and impressive specifications.

The C2-600cw is a 6.5-inch component subwoofer designed for those who seek rich, deep bass response. Its Polypropylene cone is both lightweight and rigid, ensuring optimal audio output without sacrificing clarity. The rubber surround provides added durability while also helping the subwoofer produce powerful low frequencies. Its voice coil design allows for efficient heat dissipation, enhancing performance during extended use.

The C2-600-XO is a passive crossover designed to complement the C2 series speakers. This essential component ensures that sound frequencies are directed to the appropriate drivers, thereby enhancing the overall soundstage. Constructed with high-quality materials, the C2-600-XO minimizes distortion and maximizes the efficiency of the audio system. Its design incorporates low-pass and high-pass filters to achieve a smooth transition between frequencies, making it an invaluable addition for enthusiasts aiming for precise audio reproduction.

The C2-600-02102009 model is an innovative edition within the C2 series, showcasing JL Audio’s commitment to continuous improvement and technology integration. This model features enhanced sensitivity, allowing it to produce robust sound even with lower-power amplifiers. Additionally, it employs a high-temperature voice coil and advanced cooling systems to ensure performance consistency under demanding conditions.

Across the C2 series, you'll find features such as impressive power handling and frequency response ranges. The line is engineered with a focus on sound accuracy, which allows listeners to experience the intricate nuances of their favorite music. Furthermore, installation versatility makes these models suitable for a variety of vehicles and audio setups.

In summary, the JL Audio C2 series—including the C2-600cw, C2-600-XO, and C2-600-02102009—exemplifies cutting-edge audio technology and design. Each model contributes to a dynamic, enriched listening experience, making them an excellent choice for car audio enthusiasts and audiophiles alike. The combination of robust construction and advanced acoustics ensures that these speakers not only sound exceptional but also stand the test of time in performance and reliability.