Speaker Installation

The speaker should be installed in one of the following ways depending on location:

Factory Location: If you will be using the factory speaker wires, it may be necessary to change the terminations. This may be accomplished by using an adaptor plug or simply by cutting the factory connector off and using the supplied crimp connectors to terminate the speaker wires. The large connector is for the positive terminal and the small connector is for the negative terminal of each C2-600.

You may also choose to run new speaker wires...

Run speaker wire to the desired mounting locations. If you are running wires into a door, use existing factory wiring boots whenever possible. If you are drilling new holes, file their edges and install rubber grommets into each hole. Wires should then be covered with a protective, flexible PVC sleeve and then run through the door jamb. Make sure that the wires will clear door hinges and other structures in the door. If you are unsure about any part of this process, please contact your JL Audio dealer for installation help.

!! WARNING

Double check the clearance for both speakers before proceeding. Many cars are different from one side to the other!

Your new speakers have been designed to install, without modifications, into most vehicles that accept a 6-inch (165 mm) speaker. Most factory 6 -inch speakers use four mounting screws which will line up with the mounting holes on your C2-600 speakers. Others use a 3-hole mounting system which is accommodated by a separate set of mounting holes on the frames of your C2-600 speakers.

It is absolutely vital that the speaker frame fits into the mounting hole cleanly. This must be checked prior to tightening the screws. Do not force the frame into a hole that is too small. Do not tighten the speaker onto an uneven surface. This will damage your speakers. The speaker should also fit so that air does not leak around the mounting flange. Air leaks will cause a severe degradation in sound quality. Seal any air leaks with an automotive-grade sealant material.

Install as shown in Diagram C (page 9). Use the supplied mounting clips unless the factory holes already feature threaded inserts. Hand-tighten the screws evenly to avoid bending the speaker frame!

Custom Location: Run speaker wire to the desired mounting location. If you are running wires into

a door, use existing factory wiring boots whenever possible. If you are drilling new holes, file their edges and install rubber grommets into each hole. Then, cover the wires with a protective PVC sleeve and run them through the door jamb. Make sure that the wires will clear door hinges and other structures in the door. If you are unsure about any part of this process, please contact your JL AUDIO dealer for installation help.

!! WARNING

Double check the clearance for both speakers before proceeding. Many cars are different from one side to the other!

Select an even surface. Tightening a speaker onto an uneven surface can damage it. Use the supplied template to mark the desired mounting location. Mark the center and the outline of the mounting hole as well as the mounting screw positions. Before drilling or cutting on your interior panels, use a utility knife to cut any fabric, vinyl or leather from hole locations. These materials can easily be snagged by a drill or a saw, causing damage to the panel and possible bodily injury. Drill four 1/8-inch (3 mm) holes for the speaker’s mounting screws at the positions you have marked. Also drill a pilot hole in the center of the speaker mounting hole at this time. Then, using a

saber saw, make the circular cut out for the speaker. File any rough edges. Insert the mounting clips with the flat side towards the speaker as shown in Diagram D (page 9).

The speaker should also fit so that air does not leak around the mounting flange. Air leaks will cause a severe degradation in sound quality. Seal any air leaks with an automotive-grade sealant material.

8 JL Audio - C2-600 Owner’s Manual

C2-600, C2-600-02102009, C2-600cw, C2-600-XO specifications

JL Audio is renowned for their high-performance audio equipment, and the C2 series of speakers is a testament to their commitment to quality sound. The C2-600cw, C2-600-XO, and C2-600-02102009 models are particularly noteworthy, showcasing a combination of advanced technologies and impressive specifications.

The C2-600cw is a 6.5-inch component subwoofer designed for those who seek rich, deep bass response. Its Polypropylene cone is both lightweight and rigid, ensuring optimal audio output without sacrificing clarity. The rubber surround provides added durability while also helping the subwoofer produce powerful low frequencies. Its voice coil design allows for efficient heat dissipation, enhancing performance during extended use.

The C2-600-XO is a passive crossover designed to complement the C2 series speakers. This essential component ensures that sound frequencies are directed to the appropriate drivers, thereby enhancing the overall soundstage. Constructed with high-quality materials, the C2-600-XO minimizes distortion and maximizes the efficiency of the audio system. Its design incorporates low-pass and high-pass filters to achieve a smooth transition between frequencies, making it an invaluable addition for enthusiasts aiming for precise audio reproduction.

The C2-600-02102009 model is an innovative edition within the C2 series, showcasing JL Audio’s commitment to continuous improvement and technology integration. This model features enhanced sensitivity, allowing it to produce robust sound even with lower-power amplifiers. Additionally, it employs a high-temperature voice coil and advanced cooling systems to ensure performance consistency under demanding conditions.

Across the C2 series, you'll find features such as impressive power handling and frequency response ranges. The line is engineered with a focus on sound accuracy, which allows listeners to experience the intricate nuances of their favorite music. Furthermore, installation versatility makes these models suitable for a variety of vehicles and audio setups.

In summary, the JL Audio C2 series—including the C2-600cw, C2-600-XO, and C2-600-02102009—exemplifies cutting-edge audio technology and design. Each model contributes to a dynamic, enriched listening experience, making them an excellent choice for car audio enthusiasts and audiophiles alike. The combination of robust construction and advanced acoustics ensures that these speakers not only sound exceptional but also stand the test of time in performance and reliability.