ESP 10 seconds/40 seconds:
IN ESP mode, you can select 10 seconds or 40 seconds electronic shockproof mode by using the + and - button.
4. POWER ON/OFF
Turn the device on by using any button except the REL button, EJECT key and TUNING knob on the front panel; and the LCD will display WELCOME. It can also turn on this device to insert a disc into the CD slot with label surface up. Press power button and hold for approximately 1 second to turn power off; and the LCD will display GOOD BYE.
5.LCD DISPLAY
6.CD SLOT
7&8. CD TRACK UP / DOWN AND CD FF/REW BUTTONS
Whilst in CD/MP3 mode, press the >> button briefly to play next track. Press the << button briefly to play the previous track.
Press the >> or << button and hold to skip forwards or backwards, release to resume disc playback.
9.INTRO ON/OFF BUTTON
In CD/MP3 playback process, press the INT button briefly to activate the CD track scan mode.
Whilst INTRO is on, it begins playing the first 10 second section of each song, until the last song is played. It stops the CD track scanning and begins playing the selected track when the INT button is pressed again.
10. TOP/
BUTTON
In CD/MP3 playback process, press the TOP/ 
button to pause the CD play- back, press again to resume normal playback.
First song will be played when the TOP/
button is pressed for longer than 1 second during CD/MP3 playback.
11.CD EJECT BUTTON
The loaded CD can be ejected by pressing the EJECT button. If the CD is left in the CD slot after ejection, it will reload the CD after 8 seconds.
12.MUTE ON/OFF BUTTON
This button serves to switch the MUTED state on/off.
Press the MUTE button to suppress the loudspeaker temporarily, and press again to resume listening. The muted state will be also released when the MODE, BAND, SEL and the + and - button on the front panel is pressed.
13. MODE BUTTON
When a disc is present in the CD slot, pressing the MODE button will allow you to change to RADIO mode (and back). The LCD display information changes with the mode (please note: when no disc is present in the unit, this button does not provide a function).
Page 3
WIRING DIAGRAM
ANTENNA PLUG
| YELLOW FUSE 7A |
|
|
|
|
| ||
CONSTANT B+ |
|
| RCA OUTPUT LINE |
|
|
| RED R | |
BLACK(GND) |
|
|
|
|
| |||
FUSE 0.5A |
|
|
|
| WHITE L | |||
IGNITION SWITCH | FUSE 0.5A |
|
|
| ||||
RED (B+) |
|
|
|
|
| BLUE AUTO ANT | ||
|
|
|
|
| ||||
FRONT | + | WHITE | GRAY | + | FRONT | |||
LEFT | - | WHITE/BLACK | GRAY/BLACK | - | RIGHT | |||
LOUDSPEAKER | + | GREEN | VIOLET | + | LOUDSPEAKER | |||
|
|
|
|
| ||||
REAR | - | GREEN/BLACK | VIOLET/BLACK | - | REAR | |||
Note:
1.Make sure you use a speaker with 4 ohm load impedance
2.Make sure the auto antenna wire does not come into contact with the vehicle chassis.
CAUTION:
In order to protect power IC from being burnt out during installation the car stereo, it is necessary to follow the steps below to connect the wires during installation:
Step 1: Connect the ground wire (Black);
Step 2: Connect all speaker wires and power antenna wire (Blue):
Left speaker | Right speaker | ||
Front speaker: White (+) | White/Black | Gray (+) | Gray/Black |
Rear speaker: Green (+) | Green/Black | Violet (+) | Violet/Black |
Step 3: RCA Line Out (R- Red/
Step 4: Connect Back up (Yellow) and Acc wire (Red)
Page 8