Harman-Kardon Car Stereo System owner manual Installation, Parts List, Tools and Precautions

Page 3

INSTALLATION

Parts List

Drive + Play includes the following components and parts:

Text Display With Universal Mounting Base and Attached Cable (3m)

Control Knob With 30° Mounting Base and Attached Cable (3m)

Electronics Enclosure (the Brain)

12-Volt Accessory Power Cable (2m) With Cigarette Lighter Adaptor

12-Volt Power Harness (0.5m) With In-Line Fuse Holder (for direct connection to the vehicle’s electrical system)

Line Out Cable (1.6m): Stereo 3.5mm (M) Plug to L/R RCA

(M) Plugs

iPod Cable (3m): 8-Pin Mini DIN (M) Plug to iPod Dock Connector

(2) Control Knob Bases: 0° and 60°

(2) Mounting Plates for Knob Base and Display Base

(10) Mounting Screws: (3) Knob Base, (3) Display Base and

(4) Electronics Enclosure

(6) Cable Ties, Black

(2) Hex Keys: 3mm and 1.5mm

(2) Adhesive Mounting Pads

(2) Alcohol Prep Pads

Warranty Card

Tools and Precautions

To install Drive + Play components, we recommend using the following tools:

Electric or cordless drill with drill bit set

Phillips screwdriver set

Pencil

Protective eyewear

Before starting the installation, please observe the following precautions:

Turn off all audio system power, including the iPod, before making any connections.

Always wear protective eyewear when using tools.

INSTALLATION

Choosing Installation Locations

IMPORTANT: Drive + Play should be installed according to these instructions and relevant regulations. No part of this system should obstruct the driver’s view of the road or vehicle controls or information displays necessary for safely operating the vehicle. The text display should be positioned to eliminate glare and reflections, and should be as close as possible to the driver’s normal line of sight.

Install Text Display

(on dash)

(on windshield glass)

(on gauges

 

panel)

(on dash)

 

(behind

 

radio)

Install

(in glove

Electronics

box)

 

Enclosure

 

(under

 

seat)

 

Install Control Knob

(on console)

 

Drive + Play Components

Drive + Play consists of three main components: Text Display, Control Knob and Electronics Enclosure. They operate together as a system to make controlling your iPod easy, and to route the audio signal to your mobile audio system. All three components must be installed. You can choose wireless FM transmission, wired FM transmission (adaptor sold separately), or direct con- nection of the line-output audio signal for the audio interface.

Text Display Location

The Text Display shows current iPod information and is similar to the display on your iPod. It comes with a three-position pivot arm for virtually limitless viewing adjustment. You can install the unit in a variety of locations, as long as the pro- posed site offers a direct view of the display. For easiest view- ing, mount the unit near other instrument-panel gauges or on top of the dashboard.

Control Knob Location

The Control Knob allows you to control the iPod much like the iPod Click Wheel. The unit comes with three interchangeable bases so you can choose the most comfortable operation angle. Ideally, you should install the Control Knob in a location that pro- vides comfortable access while driving where you can easily feel and operate it without taking your eyes off the road.

continued on next page...

INSTALLATION 3

Image 3
Contents Page IPod Requirements IntroductionChoosing Installation Locations InstallationParts List Tools and PrecautionsChoosing an Audio Interface Choosing a Power InterfaceAudio Input/Output Jacks Wiring DiagramInstalling Components Installing the Electronics EnclosureInstalling the Text Display Installing the Control Knob Overview Installing the iPod CableOperating Drive + Play Distraction WarningSetting Shuffle Initial SetupPower On Setting FM TransmissionSetting AUX Input Setting the DisplaySetting the Drive + Play Main Menu Browsing and Playing Songs Technical Specifications Troubleshooting
Related manuals
Manual 52 pages 19.11 Kb