E N G L I S
Remote Control Unit Preparation | Installation Guide |
E N G L I S
H
9
Battery Installation
1Remove the battery holder.
Pull the holder by the position B while pushing posi- tion A in the direction indicated by the arrow.
2Install the battery on the battery holder.
Set a new battery properly with its (i) side facing up as shown in the figure.
3Insert the battery holder.
Push in the battery holder back into its original posi- tion.
Battery Notes
Lithium battery (included)
Back side
Position B
Battery holder | Position A |
WARNING
This installation information is designed for experienced installers and is not in- tended for
Any attempt to install this product in a motor car by anyone other than qualified in- staller could cause damage to the electrical system and could result in serious per- sonal injury or death.
H
10
Remove and dispose of an old battery immediately.
Battery Information:
≥Battery type: Panasonic lithium battery (CR2025) (included)
≥Battery life: Approximately 6 months with normal use (at room temperature)
Caution:
≥Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a fire. Battery leakage may damage the unit.
≥Do not disassemble or short the battery. Do not throw a battery into a fire.
≥Keep batteries away from children to avoid the risk of accidents.
≥Be careful to the local disposal rules when you dispose of batteries.
Control Reference Guide
Buttons of the remote control function in the same way as the controls on the main unit of the reference page.
Point the remote control unit at the main unit’s sensor (REMOTE).
❐Installation Hardware
No. | Item | Diagram Q’ty |
1 | Mounting collar | 1 |
2 | Hex. nut (5 mm·) | 1 |
3 | Rear support strap | 1 |
4 | Tapping screw | 1 |
| (5 mm·a16 mm) |
|
5 | Mounting bolt (5 mm·) | 1 |
6 | Power connector | 1 |
7 | Removable face plate | 1 |
If you encounter problems, please consult your nearest professional installer.
Caution:
≥This unit operates with a 12 V DC negative ground auto battery system only. Do not at- tempt to use it in any other system. Doing so could cause serious damage.
Before you begin installation, look for the items which are packed with your unit.
≥Warranty Card…Fill this out promptly.
≥Panasonic Servicenter for Service Directory …Keep for future reference in case the product needs servicing.
≥Installation Hardware…Needed for
❐Required Tools
You’ll need a screwdriver, a 1.5 V AA battery, and
Power button (PWR) (➡ page 10)
PWR
(ATT)
MUTE
Mute button (MUTE) (➡ page 10)
case |
|
8 Trim plate | 1 |
the following: |
|
|
12 V DC | Electrical | |
Test bulb | tape | pliers |
Mode button (MODE) (➡ pages 14, 16)
Band/Disc up* button (BAND/DISC UP*) (➡ pages 14, 17)
*Only for CD changer control
(When the CD changer is connected.)
PRG
MODE
VOL
BAND/DISC UP
TUNE
TRACK
Car Audio
Volume control buttons (VOL " #)
(➡ page 10)
Tune, Track buttons
(TUNE % $, TRACK 6 5) (➡ pages 14, 16)
❐Overview
This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps:
(Please refer to the “WARNING” statement above.)
≥Identify and label the car wires.
≥Connect the car wires to the wires of the power connector.
≥Install the unit in the dashboard.
≥Check the operation of the unit.
❐Dashboard Specifications
Thickness
Min. 4.75 mm
Max. 5.56 mm
53 mm
182 mm
18 | 19 |