Panasonic CQ-VD7700U, CQ-VD7500U SP Level, SP Delay, VTR Level, Center, Front R

E N G L I

MENU: Audio Settings (for VD7700U) (continued)

E N G L I

S

H

48

: Previous menu

: Exit

Menu

Setting Value

Operations

LARGE

:

Panel

SP SETUP

for large

speakers, when bass

(continued)

playback is possible (at least

SURROUND

a

NONE

or

SMALL

SURROUND

100 Hz or lower)

or

LARGE

SMALL

:

(Surround speaker setting)

for small speakers, or when

bass playback is not possible

Remote

NONE

:

[}] or [{] a []] or [[]

when not

using surround

a [ENTER]

speakers

default: LARGE

SUB • W

YES

:

Panel

when using a subwoofer

(Subwoofer speaker setting)

SUB • W

a

NO

or

YES

A subwoofer (option, CJ-SW38 recom-

NO

:

Remote

when not using a subwoofer

mended) is required. A power amplifier

[}] or [{] a []] or [[]

(option) is also required for connecting

default: NO

a [ENTER]

a subwoofer.

	Setting range: –12 dB to +12 dB	Panel
SP LEVEL
	(1 dB steps)	q Touch the image of the speaker you
(Speaker Level)	Default: ± 0 dB for all speakers
(Adjusting the output balance of each	A test signal (a continuous tone) is	want to set.
speaker)		w	[	: UP
	output from each speaker for
FRONT L			]	: Down
	approximately two seconds.
(Left front speaker output balance)	Adjust the output balance so that		Touch to select
	the tone appears to have the same
CENTER	volume from each speaker.
(Center speaker output balance)	Adjusting the output balance:
FRONT R	Adjust the volume of all of the other
(Right front speaker output balance)	speakers to the volume level of the
	speaker from which the test signal
R¡SURROUND	appears to be the quietest.
(Right surround speaker output bal-	¡If the speaker setting is “NONE” or
	“NO” for a speaker, the test signal
ance)
	is not output and that speaker
L¡SURROUND	cannot be selected. (a page 63)	Remote
(Left surround speaker output balance)	¡Turn [VOLUME] or press [}] or	q [}] or [{]
	[{] (VOLUME) to adjust the vol-
SUB¡W	ume of the test signal.	w [[] : UP
(Subwoofer speaker output balance)			[]] : Down

				: Previous menu
				: Exit
Menu	Setting Value			Operations
	Setting range:	Panel
SP DELAY
	Center speaker...	q Touch a speaker image. (Center or
(Speaker Delay)	0 ms to 5 ms (1 ms steps)
(Adjusting the timing with which the	Surround speakers...	Surround)
audio from each speaker reaches the	0 ms to 15 ms (1 ms steps)	w	[	: Long
listener’s position)				: Short
	1 ms = 0.001 seconds		]
CENTER	Default: 0 ms for all speakers	Remote
(Center speaker delay time setting)
SURROUND		q [}] or [{]
(Surround speaker delay time setting)		w [[] : Long
¡Make this adjustment while listening			[]] : Short
to sound.
¡If the speaker setting is “NONE” for a
speaker, that speaker cannot be
selected. (a page 63)

VTR LEVEL								Panel
			Lower			Higher
									]	: Lower
(Setting the VTR (VTR1/VTR2) input		–6 dB			–4 dB		–2 dB
Level)									[	: Higher
Make this setting if it is not possible to		±0 dB			+2 dB		+4 dB	Remote
adjust the volume through the con-		+6 dB		: Input level
nected device (on the output side).					default: ±0 dB				[]] : Lower
	Notes:								[[] : Higher
Note: This setting is adjustable for an	¡If the input level from
external device that is connected to	VTR1/VTR2 is too high, the
VTR1 or VTR2. (e.g. VCR)	audio will not be output nor-
	mally. Adjust the input level
	so that “OVER” does not
	appear.

¡After setting the input level The volume can be adjusted by turning the volume knob or pressing [}] or [{] (VOL- UME) on the remote control.

S

H

49

64 65

CQ-VD7700U/VD7500U CQ-VD7700U/VD7500U