Pelco C539M-A Section Operation, Local SAT Operations, Selecting Monitors, Selecting Cameras

SECTION 3			OPERATION
1.0 LOCAL SAT OPERATIONS	3-1	2.0	9760 SAT OPERATIONS	3-4
Selecting Monitors	3-1		Selecting Link (Satellite) Cameras.…... ............................ 3-4
Selecting Cameras	3-1		Controlling Link Cameras…………….. ............................. 3-5
Controlling Cameras	3-1		Operating Suggestions………………. ............................... 3-5
Operating Sequences	3-3	3.0	ALARM OPERATIONS
Controlling Auxiliaries	3-4			3-6
			Local SAT Alarm Response……….... ............................... 3-6
			9760 System-SAT Alarm Response…. ............................. 3-7
			SAT and SAT-Alarm Unit configurations	3-9

IMPORTANT: Initializing keyboards. For SAT SIDE, local operation, keyboards must be initialized (1) after any power cycle or (2), after the first time power is applied to a keyboard or (3), after an operator initiated reset (see Ap-

pendix 5, Default Menu reset Assignments). To initialize a keyboard, enter the number (1-4) of the monitor from which you are going to view displays, then press the MON key. You must wait five seconds (before or after you enter the number and press the MON key) to allow for power up configuration to take place, after which the number of the selected monitor appears on the keyboard’s LED display.

Up to 16 cameras and four monitors (minus those used as tie-lines) are available for user access and control via keyboards connected to the SAT. Access is limited by the following constraints:

1.Physical: a monitor must be available at your location.

2.Software: programmed access (local SAT programming menus) for monitor/camera use must have been partitioned for access by the user in question.

1.0 LOCAL SAT OPERATIONS

Figure 3-1

Monitor Selection

Figure 3-2

Camera Selection

Figure 3-3

Camera Step-Through

1.1 SELECTING MONITORS

1.Enter the monitor number (1-4) you want

to view.

2Press the MON button. The monitor num- ber entered should match that appearing in the keyboard LED display

1.2 SELECTING CAMERAS

1.Enter the camera number (1-16) you want to view.

2.Press the CAM button. The camera view appears on the selected monitor.

1.3 CONTROLLING CAMERAS

1.3.1Multi-Speed PAN and TILT Control, KBD200

Use the KBD200’s “Touch Speed” feature to op- erate pan and tilts equipped with variable- speed.

Enter a number between 1 (slowest) and 9 (fast- est) followed by one of the pan and tilt buttons. The selected speed remains in the switcher’s memory until it is changed. Entering zero re- sets the pan and tilt speed to about 20 degrees per second.

1.3.2Variable-Speed PAN and TILT Control, KBD300/KBD300V

Use the joystick to operate variable-speed pan and tilt control from the KBD300/KBD300V.

Pan and tilt response increases as the joystick is deflected from its normal position. Slight de- flection causes slow pan and tilt response while full deflection causes rapid response.

1.3.3 Step Through System Camera

Use the PREV (backward) and NEXT (for- ward) buttons to step through the system cam- eras, or those cameras partitioned for your key- board location. The displayed camera order does NOT follow that set up in the CAMERA SEQUENCE sub-menu of the monitor pro- gramming menu (see the Monitor Program- ming Menu-Page 2 of 3). Those settings effect sequence operations only. Instead, at each press of the button, the SAT will stop, in turn, at each video input on the unit. What you see displayed is influenced by the following items:

1.If any SAT input lacks a display source, you will only see a blank screen. For ex- ample, if the unit is supplied with input video on 1 and 16 only and no other in- puts, then pressing NEXT or PREV while between these end-points will result in a blank screen display. Moreover, you will have to press the key 14 times to navi- gate from either end to the other.

2.The situation in (1) can be avoided if the MON to CAMERA sub-menu, located in Section 2’s, Access Programming Menu, is configured to bypass those un- used (or perhaps, unallocated) video in- puts. Now, when the NEXT or PREV button is pressed, you navigate directly from input 1 to 16, if the NEXT button is pressed and from input 16 to 1 if the PREV button is pressed.

NOTE: There is no indication on the keyboard display that you are actually viewing the camera you chose. This can be rectified by entering appropriate camera titles for each cam- era view when programming local SAT menus.

OPERATION CM9760-SAT 3-1