Memory Options, Time Features | Kenwood H2EC specs

KEN.4064 H2EReceiver/Car Man 11/19/04 9:44 AM Page 24

screen is different in that it will stay until you press the Control Knob, the Menu button, or the remote Select button. This allows you to stay in this mode while you adjust the antenna location to your satisfaction.

24Memory Options

This submenu has options that allow you to turn on or off the S-Seek feature (pop-ups to tell you that your selected songs are playing), and to clear all the songs stored with the Memo button.

Auto Memory Search

This is an on/off selection to enable or disable S-Seek pop-ups and alerts. Use the Control Knob (or the remote CH buttons) to select “On” or “Off.” Press the Control Knob (or the remote Select button) to accept the current setting.

Clear All Memory

This option will clear all the songs stored with the Memo button. Use the Control Knob (or the remote CH buttons) to select “Yes” or “No.” Selecting “Yes” will remove all the songs stored by S-Seek, and thereby remove all alerts.

Time Features

This menu option allows you to control the clock, alarm, program alerts, and other features that use Here2Everywhere’s internal clock.

Here2Everywhere has an internal clock which auto- matically picks up Universal time from the SIRIUS broadcast. After you set the Timezone and Daylight Savings Time features, the clock will always keep accurate time. However, the clock does require the SIRIUS signal after the unit is connected to power each time before it is valid. After you dock or power Here2Everywhere, allow a few seconds to acquire the clock signal.

The Time Features menu option presents the following submenu choices:

•Clock

•Alarm Clock

•Program Alert

•Auto Shutdown

•Sleep Mode

Clock

Selecting this menu option allows you to setup the clock that is shown on the default display.

The following options appear in this submenu:

•Format

•Time Zone

•Daylight Savings Time

Pressing the Select button enters the selected submenu. Pressing the Menu button returns to

the Time Features submenu. Clock: Format

This option allows you to select between 12-hour format and 24-hour format.

Clock: Time Zone

This option allows you to select one of the following time zones:

•(GMT -9:00) Alaska

•(GMT -8:00) Pacific (Factory Default)

•(GMT -7:00) Mountain

•(GMT -6:00) Central

•(GMT -5:00) Eastern

•(GMT -4:00) Atlantic

•(GMT -3:30) Newfoundland

Clock: Daylight Savings Time

This option sets whether or not your location observes daylight savings time (not whether DST is in effect— this is transmitted in the SIRIUS broadcast).

Alarm Clock

This menu option allows you to set Here2Everywhere to turn itself on at a selected time, or, if the unit is already on, beep and flash the display. The last active channel prior to shutdown will be activated when the Alarm goes off.

The submenu below gives you two options:

•Set Alarm (or Clear Alarm, if it is already set)

•Alarm Time

Alarm Clock: Set Alarm

This option allows you to enable or disable the

alarm, itself.25 Note: When the alarm function is enabled, the

clock on the default screen will be highlighted. Alarm Clock: Alarm Time

In this mode, you can change the alarm time as follows: Use the Control Knob (or the remote CH buttons) to select the hour. Press the Control Knob (or the remote Select button) to save the hour, and move the selection to the minutes. Use the Control Knob to select the minutes, and press the Control Knob (or the remote Select button) to save it. Use the Menu button to cancel changes and exit back to the Alarm Clock submenu.

Note: If Here2Everywhere is off (but with power while in the Cradle) when the Alarm time comes, it will power itself on and present the option, “Press Band to Snooze”. The Snooze option is a 9-minute delay until the alarm goes off again. Also, you can press the Power ( ) button to cancel the alarm and shut Here2Everywhere back off or any other key to simply cancel the alarm and go to music.