Audison LR 605 XR manual Controls and Functions Configuration of Connecting Clamps

CONTROLS AND FUNCTIONS

CONFIGURATION OF CONNECTING CLAMPS

INDICATOR LIGHTS

LEVEL

CONTROLS

MODE

OUTPUT CLAMPS

ON

Lit when the amplifier is on.

SAFE

When lit, it indicates the intervention of protection circuits: in case of overheating (temperature exceeding 80°C/176°F) or output anomalies (pre- ence of continuous current, short circuit or dangerously low load impedan- ce). When protection circuits intervene, the amplifier shuts down. Turn the amplifier off. When the problem is corrected, turn the amplifier back on.

V1 - V2 - V3

Level adjustments for

SUB, FRONT/WOOFER

and REAR/MID-TW channels (channels vary according to the MODE switch configuration).

F/R
Front/Rear
In	this

c o n f i g u ra t i o n ,

the amplifier

allows the realisation of a Hi Pass FRONT

SUB			FRONT
Power	output for		Left and Right power outputs for
SUB channels. It is			FRONT channels. They are Hi
Lo Pass filtered, in a			Pass filtered, in a range of
range of frequencies			frequencies between	50Hz and
between		50Hz and	150Hz (12dB/Oct.),	adjustable
150Hz	(24dB/Oct.),		through F2. The available signal is
adjustable		through
			STEREO. (Bridge configuration is
F . The		available

REAR

Left and Right power outputs for REAR chan- nels. They are Hi Pass filtered, in a range of fre- quencies between 50Hz and 150Hz (12dB/Oct.), adjustable through F3.

1

+Hi Pass REAR

+SUB system.

1	is MONO.	not possible).
signal

(Mix L + R).

The available signal is STEREO. (Bridge confi- guration is not possible).

MULTICH. Multichannel

Inthis c o n f i g u r a t i o n ,

the amplifier

allows the realisation of a two-way FRONT + SUB system.

SUB

Power output for SUB channels. It is Lo Pass filtered, in a range of frequencies between 50Hz and 150Hz (24dB/Oct.), adjustable through F1. The available signal is MONO. (Mix L + R).

WOOFER

Left and Right power outputs for WOOFER channels. They are Hi Pass filtered, in a range of fre- quencies between 50Hz and 150Hz (12dB/Oct.), adjustable through F2,and Lo Pass filtered, in a range of frequencies between 150Hz and 850Hz (12dB/Oct.), adjustable through F4. The availa- ble signal is STEREO. (Bridge configuration is not possible).

MID-TW

Left and Right power out- puts for MID-TW chan- nels. They are Hi Pass fil- tered, in a range of fre- quencies between 150Hz and 850Hz (12dB/Oct.), adjustable through F4. The available signal is STEREO. (Bridge confi- guration is not possible).

1

	MODE			FREQUENCY CONTROLS
F/R			F1		F2	F3	F4
Front/Rear			Lo pass cut-		Hi pass cut-	Hi pass cut-	N o t
In	this		off frequency		off frequency	off frequency	active.
configuration,			of	SUB	of FRONT	of REAR
the	amplifier		channel.		channels.	channels.
allows		the	(50Hz-150Hz		(50Hz-150Hz	(50Hz-150Hz
realisation		of	24dB/Oct.)		12 dB/Oct.)	12dB/Oct.)
a	Hi Pass
FRONT +		Hi
Pass REAR +
SUB system.

AUXILIARY	GENERAL
OUTPUT/INPUT	INPUT
IN REAR	IN FRONT
Input used to	General	input
drive REAR	to drive	SUB
channels.	and FRONT Hi
	Pass channels.

1

MULTICH.

F1

F2

F3

F4

pass

cut-

OUT MID-TW

IN FRONT

Multichannel

Lo pass cut-

Hi pass cut-

N o t

Lo

H i - p

a s s

General input to

In

this

off frequency

off frequency

active.

off

frequency

p r e a m p l i f i e d

drive

SUB,

configuration

of

SUB

of WOOFER

for

WOOFER

output of

MID-

WOOFER

and

,

the

channel.

channels.

channels, and

TW filter

for a

M I D - T W

a m p l i f i e r

(50Hz-150Hz

(50Hz-150Hz

Hi-pass

for

supplementary

channels.

allows

the

24dB/Oct.)

12dB/Oct.)

M I D - T W

amplifier.

realisation of

channels.

Signal level:

a two-way

(150Hz-850Hz

0 dB.

FRONT

+

12dB/Oct.)

SUB system.

REMOTE					SUB VOL.			POWER SUPPLY
					CONTROL			CLAMPS
IN	OUT				VCR01			POWER
Turn on control for the	Output	leading to		other	Connection			Input clamps		for the
amplifier coming from radio-	amplifiers of the			sound	clamps		for	amplifier power supply.
cassette player (or from any	system. It has to be				the	remote		Connect	the	battery
sources provided with remote	connected to the REMOTE				v o l u m e			positive	and	negative
control for amplifiers).	IN of the following amplifier				c o n t r o l ,			according	to	indicated
	to allow	the	simultaneous
Applied voltage must be					V C	R 0	1	polarities.
between 7 and 15 VDC.	turning	on	of the	whole	(optional).			Applied voltage must be
	system. Available voltage
								between 11 and 15 VDC.
	equal to REMOTE IN.

10 11