Audio Level, Antenna Aiming, Memory Options

KEN.4061 ReceiverCarHome Manual 11/19/04 9:37 AM Page 26

To enter a code:

1.Turn the Control Knob (or use the remote 0-9 buttons) to select the first digit of the code.

2.Press the Control Knob (or the remote Select button) to keep that digit, and move to the

26	next digit.
	3. Repeat these steps until all four digits are entered.

assigned preset. In either case, you will be prompted to enter the 4-digit code before the system will tune to the channel, play audio from the channel, or display text information from the channel. When the code is accepted, the channel will play until you change channels or until Here2Everywhere is turned off.

level on the stereo mini-jack to better match the stereo system. Kenwood recommends leaving this at the factory default level unless it is necessary to change it. The most common use for this setting is to adjust headphone volume levels if you are using headphones directly plugged into the cradle.

Note: Most Menu screens automatically exit after a
few seconds without user input. The Antenna Aiming
screen is different in that it will stay until you press the
Control Knob, the Menu button, or the remote Select
button. This allows you to stay in this mode while you
adjust the antenna location to your satisfaction.	27

Here2Everywhere will ask for the 4-digit code a sec- ond time, to confirm.

All future entries into the Lock/Unlock submenu will display the text “Lock/Unlock” on the top line and a channel list below it.

1.Use the Control Knob (or the remote CH buttons) to highlight the channel you want to lock. (The highlighted channel will automatically play.)

2.Press the Control Knob (or the remote Select button) to change the highlighted channel’s status. The word “lock” will appear after the channel name.

3.To remove the “lock” from the channel, press the Control Knob (or the remote Select button) again.

•To exit the Lock/Unlock function, press the Menu button.

Note: Locked channels can be accessed only by the Remote’s Direct Tuning feature or by a previously

Note: To permanently remove the lock status from the channel, return to the Lock/Unlock submenu option and follow the previous steps.

Edit Code

Use this submenu option to change the 4-digit code, [0000]. On entering this submenu option, you will be asked to enter the 4-digit code as described in the previous section. Once the correct code has been entered, you will be prompted to enter a new 4-digit code, twice. The second entry is requested for confirmation. Once confirmed, the display will return to the Lock Options menu.

Audio Level

This menu option allows you some control over the volume of Here2Everywhere. This is used in setting up Here2Everywhere with a home or vehicle stereo. Typically, you will use the home or vehicle stereo volume control after this setting is correct. This set- ting can be used to raise or lower the output signal

Antenna Aiming

Upon selecting this option, Here2Everywhere’s top line displays two 10-segment horizontal bar graphs:

One is labeled “SAT,” and shows the satellite signal strength. The other is labeled “TER,” and indicates the strength of the terrestrial (ground- based) SIRIUS signal. The terrestrial SIRIUS signal is only present in cities.

Moving the antenna location may adjust the bar graph signal strength indications and insure opti- mum reception. Pressing the Control Knob, the menu button, or the remote Select button returns to the top level Menu Options.

Memory Options

This submenu has options that allow you to turn on or off the S-Seek feature (pop-ups to tell you that your selected songs are playing), and to clear all the songs stored with the Memo button.

Auto Memory Search

This is an on/off selection to enable or disable S-Seek pop-ups and alerts. Use the Control Knob (or the remote CH buttons) to select “On” or “Off.” Press the Control Knob (or the remote Select but- ton) to accept the current setting.

Clear All Memory

This option will clear all the songs stored with the Memo button. Use the Control Knob (or the remote CH buttons) to select “Yes” or “No.” Selecting “Yes” will remove all the songs stored by S-Seek, and thereby remove all alerts.