INSTALLATION MANUAL
DVH-P5000MP
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est con- forme à CEMA.
Printed in Japan
Imprimé au Japon
<KSNNF/03C00001> |
MANUEL D’INSTALLATION
Connecting the Units
Notes
•This unit is for vehicles with a
•To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.
•Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.
•Secure the wiring with cable clamps or adhe- sive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.
•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, hand- brake, and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short- circuiting to the vehicle body.
•Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.
•Do not shorten any leads. If you do, the protec- tion circuit may fail to work when it should.
•Never feed power to other equipment by cut- ting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.
•When replacing fuse, be sure to use only fuse of the rating prescribed on this unit.
•Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right ≠ speaker leads are common.
•Speakers connected to this unit must be high- power types with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speak- ers with output and/or impedance values other than those noted here may result in the speak- ers catching fire, emitting smoke, or becoming damaged.
•When this product’s source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp’s sys- tem remote control or the car’s
•When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal.
Likewise, do not connect the blue/white lead to the power terminal of the
•To avoid
•To prevent incorrect connection, the input side of the
Connecting the Units
•If this unit is installed in a vehicle that does not have an ACC (accessory) position on the igni- tion switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. (Fig. 1)
|
| CC |
|
|
|
|
|
|
|
|
| F | A | O |
|
|
| F | O |
|
|
|
| N |
| N | ||||||
O | F |
|
|
|
| O | F |
|
|
|
|
|
|
| S |
|
|
| S | ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| T |
|
|
|
| T |
|
|
|
| R | A |
|
|
| R | A |
|
|
| T |
|
|
| T |
| ||
|
|
|
|
|
|
|
|
| ||
ACC position | No ACC position | |||||||||
Fig. 1
•The black lead is ground. Please ground this lead separately from the ground of
If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.
•Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the sup- plied Installation manuals of both products and connect cords that have the same func-
tion.