Installation, Using the Speaker Input | Pioneer GM-6300F specs

Connecting the Unit

ENGLISH

Installation

ENGLISH

Using the Speaker Input

Connect the car stereo speaker output wires to the amplifier using the supplied speaker input connector.

• Do not connect both the RCA input and the speaker input at the same time.

7Connections when using the speaker input

Green: CH B, Left +

	Green/black: CH B, Left ≠
	Violet/black: CH B, Right ≠
	Violet: CH B, Right +	Car Stereo
	Gray: CH A, Right +	Car Stereo
	Gray: CH A, Right +
	Gray/black: CH A, Right ≠
Speaker input connector		Speaker output
To speaker input termi-
nal of this unit.	White/black: CH A, Left ≠
	White/black: CH A, Left ≠
	White: CH A, Left +

Connecting the Speakers and Input Wires

The speaker output mode can be four- channel, three-channel (stereo + mono) or two-channel (stereo, mono). Connect the speaker leads to suit the mode according to the figures shown below.

•In the case of four-channel or three- channel mode, if only one input plug is used, such as when the car stereo has only one output (RCA output), connect the plug to RCA input jack A, but do not connect a plug to RCA input jack B.

•In the case of two-channel mode connect RCA plugs to the RCA input jack A.

Four-channel mode

(Right) Speaker out A (Left)

+≠≠+

(Left) Speaker out B (Right)

Three-channel mode

(Right) Speaker out A (Left)

+≠≠+

+≠

Speaker out B (Mono)

Two-channel mode (Stereo)

Speaker (Right)

+≠

≠+

Speaker (Left)

Two-channel mode (Mono)

Speaker (Mono)

≠

+≠

Speaker (Mono)

CAUTION

• Do not install in:

—Places where it could injure the driver or pas- sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s seat.

•Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-cir- cuit.

•Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage.

•Install tapping screws in such a way that the screw tip does not touch any wire. This is impor- tant to prevent wires from being cut by vibration of the car, which can result in fire.

•DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

•To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down.

•Never replace the fuse with one of greater value or rating than the original fuse. Use of an improp- er fuse could result in overheating and smoke and could cause damage to the product and injury including burns.

CAUTION:

To prevent malfunction and/or injury

•To ensure proper heat dissipation of the amplifier, be sure of the following during installation.

—Allow adequate space above the amplifier for proper ventilation.

—Do not cover the amplifier with a floor mat or carpet.

•Do not install the amplifier on unstable places such as the spare tire board.

•The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location.

•Make temporary connections first and check that the amplifier and the system operate properly.

•After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.

Example of installation on the floor mat or on the chassis

1.Place the amplifier where it is to be

installed. Insert the supplied tapping screws (4 ⋅ 18 mm) into the screw holes. Push on the screws with a screwdriver so they make marks where the installation holes are to be located.

2.Drill 2.5 mm (1/8 inch) diameter holes at the point marked, and install the amplifier, either on the carpet or directly to the chassis.

Tapping-screws

(4 ⋅ 18 mm)

Drill a 2.5 mm (1/8 inch)
	Floor mat
diameter hole	or chassis

GM-6300F specifications

The Pioneer GM-6300F is a high-performance amplifier designed to elevate the audio experience in a vehicle. Renowned for its reliability and sound quality, this amplifier incorporates advanced technologies and features that make it a compelling choice for both casual listeners and audiophiles alike.

One of the standout characteristics of the GM-6300F is its power capability. It delivers 600 watts of maximum power, effectively driving any speaker setup with robust audio output. With a four-channel configuration, the amplifier allows for versatile installation options, providing users the flexibility to run either front and rear speakers or to bridge channels for a more powerful subwoofer experience.

Pioneer has employed Class D technology in the GM-6300F, ensuring high efficiency while keeping the unit compact and lightweight. This means that the amplifier can produce high-quality sound without drawing excessive power or generating too much heat, which is particularly important in tight automotive spaces. The compact design also ensures it can easily fit into various installations without compromising on performance.

Another notable feature of the GM-6300F is its comprehensive onboard crossover system. The adjustable high-pass and low-pass filters enable users to fine-tune the audio output, allowing them to optimize the sound for their specific speaker setup. This customization is further enhanced by the inclusion of a bass boost function, which can enhance low-frequency audio performance, making it ideal for bass-heavy genres.

Pioneer has also integrated advanced protection circuitry into the GM-6300F. This includes short circuit protection, thermal protection, and overcurrent protection, ensuring the amplifier operates reliably under demanding conditions. Such features contribute to the overall longevity of the device, making it a worthy investment for car audio enthusiasts.

The amplifier features RCA inputs, allowing easy connection to a variety of head units and other audio sources. Its sleek design, coupled with a brushed aluminum finish, adds an aesthetic appeal that complements modern car interiors.

Overall, the Pioneer GM-6300F stands out with its powerful performance, innovative technologies, and user-friendly features, making it an excellent choice for anyone looking to enhance their in-car audio system. Whether it’s for daily driving or in-depth listening sessions, the GM-6300F offers a satisfying and immersive audio experience.