Pioneer AVH-P7600DVD installation manual Español Deutsch Français Italiano Nederlands

Page 3

Note:

This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recre- ational vehicle, truck, or bus, check the battery voltage.

To avoid shorts in the electrical system, be sure to disconnect the battery cable before beginning installation.

Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.

Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insu- lation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.

Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

Do not shorten any leads. If you do, the protection circuit may fail to work when it should.

Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder.

Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right speaker leads are common.

If the RCA pin jack on the unit will not be used, do not remove the caps attached to the end of the connector.

Speakers connected to this unit must be high- power with minimum rating of 50 W and imped- ance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged.

When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction.

To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the unused speaker leads without fail. There is a possibility of a short-circuit if the leads are not insulated.

To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same col- ors correctly.

This unit cannot be installed in a vehicle that does not have an ACC (accessory) position on the ignition switch. (Fig. 1)

 

 

CC

 

 

 

 

 

 

 

 

 

F

A

O

 

 

 

F

O

 

 

 

F

 

N

 

N

O

 

 

 

 

O

F

 

 

 

 

 

 

 

S

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

 

T

 

 

 

T

R

A

 

 

 

R

A

 

 

 

 

 

 

T

 

ACC position

No ACC position

Fig. 1

The black lead is ground. Please ground this lead separately from the ground of high-current prod- ucts such as power amps.

If you ground the products together and the ground becomes detached, there is a risk of dam- age to the products or fire.

Cords for this product and those for other prod- ucts may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the

same function.

English

Español

Deutsch Français Italiano

Nederlands

2

Image 3
Contents Installation Manual Contents Connecting the UnitsEspañol Deutsch Français Italiano Nederlands Connecting the system Connecting the power cord Left Español Rear Output When connecting to separately sold power ampEspañol Deutsch Français Italiano When connecting with a rear view camera Français Italiano Nederlands When using a display connected to rear video output When connecting the external video component and the displayAttaching the noise filters Mounting with Velcro Tape Installing the hide-away unitDIN Front-mount Before installing the unitInstallation with the rubber bush DIN Front/Rear-mountDIN Rear-mount Installation using the screw holes on the side of the unitFixing the front panel Installing the remote control unitAvertissement Table des matièresEnglish Raccordement du système Branchement du cordon d’alimentation Gauche Avertissement Center Output Droit Raccordements à une caméra de recul Précaution Avertissement Raccordements à un appareil vidéo externe et à un écranFixation des filtres de bruit Fixation avec la bande Velcro Installation de l’appareil déportéMontage DIN avant Avant d’installer l’appareilInstallation avec une bague en caoutchouc Montage DIN avant/arrièreMontage DIN arrière Installez l’appareil dans le tableau de bord. FigFixation du panneau avant Installation du boîtier de télécommandePioneer Corporation