CONTROLS AND FEATURES (cont'd)
< Rear Panel > 24 | 25 |
IN OUT
AC IN 
DC IN
12V
+
-
CUT OFF
1
B
2
R
G
DRIVE
R
1
G
2
SET UP
VIDEO A
IN 
OUT
VIDEO B
IN 
OUT
IN
Y/C
OUT
EXT SYNC
IN 
OUT
AUDIO
IN OUT
A
B
NORMAL
AFC
FAST
TALLY/
REMOTE
A 
B
NORMAL
AFC
FAST
21
TALLY/
REMOTE
22 Power input connector
Supply power to either the AC IN or DC IN 12 V connector.
[AC IN]
22
To AC outlet
(120 V AC, 50/60 Hz)
23
21 TALLY/REMOTE terminal
External control terminal (DIN
Note:
*When you’re controlling the monitor externally via the TALLY/REMOTE terminal, set all corresponding switches on the front panel to the OFF
TALLY/REMOTE terminal pin layout
|
| GND |
|
|
|
COLOR OFF | OFF |
|
| OFF | PULSE |
|
| CROSS | |||
| ON |
|
| ON |
|
UNDER |
| 7 | 6 |
|
|
SCAN | OFF | 8 |
| OFF | TALLY |
| ON | 3 | 1 | ON |
|
ASPECT |
| 5 | 4 |
| EXT |
4:3 | 2 |
| OFF | ||
RATIO |
|
| SYNC | ||
| 16:9 |
|
| ON |
|
INPUT | A |
|
|
|
|
SELECT |
|
|
|
|
B
Pin No. |
| Signal |
|
|
|
1 | TALLY lamp | ON/OFF |
|
|
|
2 | Input Select | A/B |
| (VIDEO A/B) |
|
|
|
|
3 | UNDER SCAN | ON/OFF |
|
|
|
4 | EXT SYNC | ON/OFF |
| (External Sync) |
|
|
|
|
5 | ASPECT RATIO | 4 : 3 /16 : 9 |
| (4 : 3 /16 : 9) |
|
|
|
|
6 | PULSE CROSS | ON/OFF |
|
|
|
7 | COLOR OFF | ON/OFF |
|
|
|
8 | GND |
|
|
|
|
Connect the provided AC power cord between the AC IN connector and an AC outlet (120 V AC, 50/60 Hz).
[DC IN 12 V]
Connect the 12 V DC power plug to the DC IN 12 V connector.
Notes:
*See your dealer for more information on 12 V DC power supply.
*When both AC IN and DC IN connectors are used, the AC input has priority.
*The DC power supply does not automatically take over if an AC outlet is unplugged or the AC power is cut off when both AC and DC power supplies are connected. In this case, press the POWER switch to set to OFF, then press it again to turn the power ON.
DC IN 12 V connector pin layout
DC IN |
| Pin No. | Signal |
12V | 3 | 1 | GND |
| |||
|
| ||
4 |
| 2 | — |
| 2 | 3 | — |
1 |
| 4 | 12 V DC |
23 Power cord
Connect the provided power cord to the AC IN connector.
24 External battery mounting holes
Attach an external battery to either pair of holes (1 or 2) to use 12 V DC power (depending on the type of battery).
Notes:
*External batteries manufactured by Anton Bauer or PAG are available.
*See your dealer for details.
25 Switch/control adjustment holes for service personnel
For adjustment of SET UP switch, CUT OFF (B, R, G) control and DRIVE (R, G) control during servicing.
Note:
*These controls are exclusively for the use of service personnel. Do not attempt to adjust them yourself.
6